Accessories

出色的射頻效能

• 等效輸出 SWR：1.33
• 最大輸入功率：0.5 W
• 插入損耗：7 dB
• 追蹤任兩個連接埠之間：0.20 dB 至 8 GHz

以 Keysight 8757 純量網路分析儀做寬頻比量測時，建議使用 Keysight 11667A 功率分配器。 此雙電阻型電源分配器用於電源位準調整或等比量測應用時，可在輔助臂上提供出色的輸出 SWR。 追蹤頻率範圍從 dc 至 18 GHz 的輸出臂之間可以用最小的不確定性量測寬頻。

• 頻率範圍：2 Hz 到 26.5 GHz
• 最大 SWR：1.45 1 GHz 到 18 GHz、1.60 18 GHz 到 26.5 GHz
• 插入損耗：1.2 dB 1 GHz 到 18 GHz、1.4 dB 18 GHz 到 26.5 GHz
• 隔離值：19 dB 1 GHz 到 18 GHz、18 dB 18 GHz 到 26.5 GHz
• 最大振幅追蹤：0.3 dB 0.5 GHz 到 18 GHz、0.5 dB 18 GHz 到 26.5 GHz
• 最大相位追蹤：6 deg - 0.5 GHz 到 18 GHz，10 deg - 18 GHz 到 26.5 GHz

• Frequency range: DC to 50 GHz
• Maximum SWR: 1.67 at 50 GHz
• Insertion loss: 8.5 dB at 50 GHz
• Maximum amplitude tracking: 0.3 dB
• Maximum phase tracking: ± 2°

The Keysight 11636C is a DC to 50 GHz power divider that provides highly accurate direct power dividing and combining. Excellent phase and amplitude tracking ensure accurate impedance matching of all three ports, which improves the fault location measurement by reducing re-reflections and intermodulation distortion.

卓越的RF效能

• 等效輸出 SWR：1.78
• 最大輸入功率： 0.5 W
• 插入損耗： 6.6 dB
• 雙埠之間的追蹤： <0.2 dB

Keysight 11667L 為 50ohm、雙電阻式功率分離器，具有BNC插頭。它可與Keysight E5061B 網路分析儀搭配使用，以便用於電力傳輸網路量測，例如使用shunt-thru法（100 Hz至10 MHz）執行DC-DC 轉換器輸出阻抗量測。它提供了優異的振幅（<0.2 dB） 與相位追蹤（+/-3），可確保功率分離的精確度與低駐波比（SWR），以大幅減少量測的不確定性。

Superior RF Performance

• Maximum SWR: 1.35
• Insertion loss: 6.0 dB typical
• Maximum amplitude tracking: 0.5 dB
• Maximum phase tracking: 2 deg typical

The Keysight 11636A is a dc to 18 GHz power divider for direct power dividing applications. The excellent impedance match of all three ports improves fault location measurements by reducing re-reflections. The Keysight 11636A power divider/combiner is recommended when making wideband comparison measurements with a Keysight 8757 scalar vector network analyzer.

• Frequency range: dc to 26.5 GHz
• Maximum SWR: 1.29
• Insertion loss: 7.5 dB
• Maximum amplitude tracking: 0.25 dB at 18 GHz
• Maximum phase tracking: 2 deg typical

The Keysight 11636B is a dc to 26.5 GHz power divider for direct power dividing applications. The excellent impedance match of all three ports improves fault location measurements by reducing re-reflections. The Keysight 11636B power divider/combiner is recommended when making wideband comparison measurements with the Keysight 8757 scalar vector network analyzer.

• Broad operating frequency range up to 67 GHz eliminates the need for multiple dividers 
• Excellent amplitude and phase tracking ensures highly accurate power division
• Low SWR minimizes measurement uncertainty

The Keysight 11636D is a DC to 67 GHz power divider that provides highly accurate direct power dividing and combining. Excellent phase and amplitude tracking ensure accurate impedance matching of all three ports, which improves the fault location measurement by reducing re-reflections and intermodulation distortion.

Superior RF Performance

• Equivalent output SWR: 1.22
• Maximum input power: 0.5 W
• Insertion loss: 7 dB
• Tracking between two ports: 0.25 dB to 18 GHz, 0.40 to 26.5 GHz

The Keysight 11667B power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxiliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 26.5 GHz allows wideband measurements to be made with a minimum of uncertainty.

• Frequency range: dc to 50 GHz
• Equivalent output SWR: 1.65
• Maximum input power: 0.5 W
• Insertion loss: 8.5 dB
• Tracking between two ports: 0.40dB

The Keysight 11667C power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxiliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 50 GHz allows wideband measurements to be made with a minimum of uncertainty.

• Broad operating frequency up to 67 GHz
• Excellent output VSWR at the auxiliary arm when used for source leveling or ratio measurement applications
• Unmatched tracking between outputs ensures minimum measurement uncertainty

The Keysight 11667D power splitter is a two-resistor type power splitter provides excellent output SWR at the auxiliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from DC to 67 GHz allows wideband measurements to be made with a minimum of uncertainty.

Superior RF Performance

• Maximum SWR: 1.45 0.5 GHz to 18 GHz, 1.60 18 GHz to 26.5 GHz
• Insertion loss: 1.5 dB 0.5 GHz to 18 GHz, 1.9 dB 18 GHz to 26.5 GHz (insertion loss is in addition to 3 dB coupling loss)
• Isolation: 19 dB

Features

• Maximum amplitude tracking: 0.3 dB 0.5 GHz to 18 GHz, 0.5 dB 18 GHz to 26.5 GHz
• Maximum phase tracking: 6 deg 0.5 GHz to 18 GHz, 10 deg 18 GHz to 26.5 GHz

The Keysight 87302C hybrid power divider is designed for power splitting applications that require minimal insertion loss and high isolation between ports. It has insertion loss between the main line and output port which is 1 to 2 dB less than equivalent resistive power splitters. It is designed for critical signal processing applications; phase and amplitude tracking between the two output ports is controlled and specified.

• Frequency range: 1 GHz to 26.5 GHz
• Maximum SWR: 1.45 1 GHz to 18 GHz, 1.60 18 GHz to 26.5 GHz
• Insertion loss: 1.2 dB 1 GHz to 18 GHz, 1.6 dB 18 GHz to 26.5 GHz (insertion loss is in addition to 3 dB coupling loss)
• Isolation: 19 dB 1 GHz to 18 GHz, 21 dB 18 GHz to 26.5 GHz
• Maximum amplitude tracking: 0.3 dB 0.5 GHz to 18 GHz, 0.5 dB 18 GHz to 26.5 GHz
• Maximum phase tracking: 6 deg 0.5 GHz to 18 GHz, 10 deg 18 GHz to 26.5 GHz
• Maximum amplitude tracking: 0.3 dB 0.5 GHz to 18 GHz, 0.5 dB 18 GHz to 26.5 GHz
• Maximum phase tracking: 6 deg 0.5 GHz to 18 GHz, 10 deg 18 GHz to 26.5 GHz

The Keysight 87303C hybrid power divider is designed for power splitting applications that require minimal insertion loss and high isolation between ports. It has insertion loss between the main line and output port which is 1 to 2 dB less than equivalent resistive power splitters. It is designed for critical signal processing applications; phase and amplitude tracking between the two output ports is controlled and specified.