Accessories

• Provides communication between the PXI VNA and external peripherals (i.e. handler)
• Enables synchronized measurements with the PXI VNA in an automated test environment
• Compatible with the 24-bit digital I/O connector of the PNA and ENA

The M9341A digital I/O with 24-bit digital I/O connector and triggering ports provides communication signals between the PXI vector network analyzer (VNA) installed in the same PXI chassis and an external handler. This allows the PXI VNA, such as the Keysight M937xA and M9485A, to operate in an automated test environment.

The M9341A digital I/O is compatible to the 24-bit digital I/O connector on the rear panel of the Keysight VNA such as the PNA and ENA Series.

• DC to 9 GHz frequency range

The Keysight 85033E calibration kit contains precision 3.5mm standards used to calibrate Keysight network analyzers. Standards include fixed terminations, open circuits, and short circuits in both genders. A torque wrench is also included for proper connection. This kit is specified from dc to 9 GHz.

Options are available to add 3.5 mm female to female, 3.5 mm male to male and 3.5 mm female to male adapters. Other options add four 3.5mm to type-N adapters or four 3.5 mm to 7 mm adapters.

• DC to 26.5 frequency range
• Calibration standards to perform full two-port calibration
• Precision 50 ohm airline for Thru-Reflect-Line (TRL) calibration
• Torque wrenches for properly connecting standards
• Adapters to change the gender of the test port
• Commercial calibration certificate

The Keysight 85052C precision mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection.

Type

• Unterminated single pole double throw EM switch
• Operating frequency from DC to 4, 20, 26.5, 40, 50 or 67 GHz
• Female SMA connectors
• Built-in current interrupt

Superior RF Performance

• Superior isolation: > 120 dB at 4 GHz and 70 dB at 26.5 GHz
• Low SWR: < 1.10 at 4 GHz and 1.60 at 26.5 GHz
• Low insertion loss: < 0.27 dB at 4 GHz and 0.80 dB at 26.5 GHz

Excellent RF repeatability & long life span

• Excellent insertion loss repeatability: 0.03 dB to 1 million cycles and 0.1 dB to 2 million cycles
• Long operating life of 2 million cycles

Features

• Coil voltage levels 5 V, 15 V or 24 V
• D-subminiature 9-pin connectors or solder lug terminals
• Standard or TTL/5 V CMOS compatible drive
• Optional position indicators

The Keysight N1810UL latching coaxial switch combines unmatched flexibility of configuration with excellent repeatability, long life, and reliability.

For additional information regarding configuration options and performance tradeoffs view the online product overview.

• Precision 2-port microwave ECal module with high accuracy
• Frequency coverage from 300 kHz to 26.5 GHz or DC to 26.5 GHz (Option 0DC)
• Fast, easy, and accurate full two-port calibration
• Supports 3.5 mm connectors
• Available in male/male (option M0M), female/female (option F0F), and male/female (option M0F) connector configurations
• Direct control from Keysight vector network analyzers via USB

The Keysight N4691D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4691D is a precision 2-port ECal module that supports 3.5 mm connectors up to 26.5 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4691D is included for securing your ECal module and accessories.

The N4691D Option 0DC extends the calibration frequency range down to DC, which is beneficial for broadband device modeling or time domain and signal integrity analysis using enhanced time domain-analysis on the Keysight network analyzers.

This ECal module is an ideal solution for calibrating vector network analyzers. Performing a full two-port calibration takes less than half the time and number of connections versus traditional mechanical cal kits. The operator simply connects the ECal module to the vector network analyzer via USB and the firmware controls the rest, thus reducing the chance for operator error. Wear and tear on connectors is reduced as well, lowering repair costs on both the test port connectors and calibration standards.

• Frequency range: 50 MHz to 18 GHz 
• Wide dynamic range of -70 to +20 dBm
• CW power sensor measures average power
• Fast measurement speed, up to 400 readings per second
• Calibration factors, linearity, and temperature compensation data are stored in EEPROM
• Excellent SWR for reducing mismatch uncertainty
• Accurate calibration and traceability to NIST
• Compatible with EPM (N1913B/14B, N1913A/14A, E4418B/19B), EPM-P (E4416A/17A) and P-series (N1911A/12A) power meters

• Frequency range: 50 MHz to 18 GHz
• Wide dynamic range for peak power measurements: -35 to +20 dBm
• Calibration factors, linearity, temperature, and bandwidth correction data are stored in EEPROM
• Zero and calibrate while connected to the DUT
• Precision Type-N connector as standard
• Sensor cable fixed to sensor and available cable lengths: 1.5m (5 ft), 3m (10 ft), and 10m (31 ft)

The N192xA wideband power sensors are the first to feature internal zero and calibration, integrating a DC reference source and switching circuits directly into the sensor. This innovation eliminates the need for multiple connections to an external calibration source, reducing connector wear, shortening test time, and minimizing measurement uncertainty.

• Precision 2-port microwave ECal module with high accuracy
• Frequency coverage from 10 MHz to 40 GHz or DC to 40 GHz (Option 0DC)
• Fast, easy, and accurate full two-port calibration
• Supports 2.92 mm connectors
• Available in male/male (option M0M), female/female (option F0F), and male/female (option M0F) connector configurations
• Direct control from Keysight vector network analyzers via USB

The Keysight N4692D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4692D is a precision 2-port ECal module that supports 2.92 mm connectors up to 40 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4692D is included for securing your ECal module and accessories.

The N4692D Option 0DC extends the calibration frequency range down to DC, which is beneficial for broadband device modeling or time domain and signal integrity analysis using enhanced time domain-analysis on the Keysight network analyzers.

This ECal module is an ideal solution for calibrating vector network analyzers. Performing a full two-port calibration takes less than half the time and number of connections versus traditional mechanical cal kits. The operator simply connects the ECal module to the vector network analyzer via USB and the firmware controls the rest, thus reducing the chance for operator error. Wear and tear on connectors is reduced as well, lowering repair costs on both the test port connectors and calibration standards.

• 2.4 mm (f)
• Open, short, and load precision standards
• DC to 50 GHz
• Load return loss 26 to 42 dB, depending on frequency

The 85563A 3-in-1 mechanical calibration standard combines an open, short and load standard in a compact unit. The product is small, easy to handle, and light weight. All standards in the 85563A are female 2.4 mm.

For more information about calibration kits, please visit Mechanical and Electronic Calibration Kits.

The Keysight 85130G test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a NMD-2.4 mm (f) to NMD-2.4 mm (m) adapter and a NMD-2.4 mm (f) to PSC-2.4 mm (f) adapter. The frequency range for these adapters is dc to 50 GHz with a return loss of 23 dB or better.

The Keysight 85130F test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 2.4 mm to PSC-3.5 mm male adapter and a 2.4 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 26 dB or better.

The Keysight 85130D test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to PSC-3.5 mm male adapter and a 3.5 mm to PSC-3.5 mm female adapter. The frequency range for these adapters is dc to 26.5 GHz with a return loss of 28 dB or better.

For more information about 3.5 mm cables and adapters, please visit Cables for Network Analyzers with 3.5 mm Test Ports.