Accessories

• Test and validate high-speed technologies such as DDR5 / MIPI with the 25 GHz probe amplifier (AP2).
• Experience the highest input impedance in midband frequencies for low-energy probing.
  
• Boost test margins with the lowest signal degradation.
• Probe small devices with the super-flexible micro probe head or choose from the widest variety of compatible probe heads for your unique application.
• Measure differential, single-ended, and common mode signals with a single probe tip.
  
• Use with Infiniium UXR-, 90000 X-, Q-, V-, and Z-Series oscilloscopes.

Keysight’s MX0025A InfiniiMax Ultra Series probe amplifier improves usability because you can measure differential, single-ended, and common mode signals with a single probe tip.

When you use a probe to connect your signal to your oscilloscope, it becomes part of the circuit affecting your test. Your probe may be hiding signal details, loading down your signal, or distorting it. InfiniiMax Ultra Series probes have the lowest loading for minimal impact to your circuit. Boost your test margins and gain measurement confidence with their unprecedented accuracy. Ensure your entire measurement system is helping you see the truest representation of your signal.

These probes have the lowest noise and capacitive loading and the lowest loading across more frequencies due to their RC high impedance profile. The InfiniiMax Ultra Series supports InfiniiMode and has a user-defined AC calibration mode, a wider input voltage range, more accuracy with unique S-parameter characterization, lower capacitive loading, a wider input voltage range, micro / socketed probe heads for smaller density probing, and more bandwidths. The InfiniiMax Ultra Series has an RC input impedance architecture with the lowest loading and least signal distortion across the widest frequency range.

InfiniiMax Ultra probes have three attenuation ranges — 1:1, 4:1, and 8:1 — giving you superior noise performance and large voltage ranges, all while maintaining maximum bandwidth. The input range automatically configures depending on the size of the input signal and vertical scale of your oscilloscope.

Choose from the three flexible input dynamic ranges from 600 mVpp at 1:1, 2.5 Vpp at 4:1, and 5 Vpp at 8:1. Clearly see and know when your design is satisfactory, keep up with standards, easily probe small devices, and reduce test complexity with the InfiniiMax Ultra Series probes.

• Maximum voltage: 42 V
• Termination: 5 single banana plugs (4-wire measurements plus ground)
• Length: cable is 0.8 meters (31.5 inches)

The Keysight kelvin probe set consists of two gold-plated flat tweezers with special gripping surfaces. This design assures a very precise contact to the component and very precise measurements. The ground guard connector removes ground-related errors. The gold plating helps to reduce the contact resistance between the surfaces of the test probe and the lead of the component being measured - reducing overall error!

The Keysight 11059A is compatible with the Keysight 34460A, 34461A, 34401A, 3458A, 34410A, 34411A, 34465A, 34470A digital multimeters and B2900 series precision source / measure units.

Bandwidth:

• Bandwidth: 7 GHz

Range:

• Dynamic Range: +/- 2.5V
• DC Offset Range: +/- 12V when using probe offset
• Maximum Voltage: +/- 30V

Input Impedance:

• Differential Input R: 50 kOhm
• Differential Input C: 0.27-0.34 pF
• Single Ended Input R: 25 kOhm
• Single Ended Input C: 0.44-0.67 pF

For high-speed differential or single-ended probing in embedded designs, the InfiniiMax 7 GHz 1134B differential probe amplifier is a perfect complement to Infiniium 6 GHz oscilloscopes. Its extremely low input capacitance, flat frequency response and resistor probe tip technology provide ultra-low loading of the DUT and superior signal fidelity. The InfiniiMax 1130B-34B Series supports a wide variety of real-world applications with an extensive line up of probe heads and accessories. The accessories can meet the most demanding mechanical access requirements.

The 1134B is the RoHS compliant version of the 1134A. The 1134B is 100% form, fit, function and price equivalent to the 1134A.

To see the other available probe head accessories for InfiniiMax 1130B-34B, visit InfiniiMax probe accessories.

Learn more about Oscilloscope Single-Ended Active Probes

Bandwidth:

• 5 GHz

Range:

• Dynamic Range: +/- 2.5V
• DC Offset Range: +/- 12V when using probe offset
• Maximum Voltage: +/- 30V

Input Impedance:

• Differential Input R: 50 kOhm
• Differential Input C: 0.27-0.34 pF
• Single Ended Input R: 25 kOhm
• Single Ended Input C: 0.44-0.67 pF

For high-speed differential or single-ended probing in embedded designs, the InfiniiMax 5 GHz 1132B differential probe amplifier is a perfect complement to Infiniium 4 GHz oscilloscopes. Its extremely low input capacitance, flat frequency response and patented resistor probe tip technology provide ultra-low loading of the DUT and superior signal fidelity. The InfiniiMax 1130B-34B Series supports a wide variety of real-world applications with an extensive line up of probe heads and accessories. The accessories can meet the most demanding mechanical access requirements.

The 1132B is the RoHS compliant version of the 1132A. The 1132B is 100% form, fit, function and price equivalent to the 1132A.

To see the other available probe head accessories for InfiniiMax 1130B-34B, visit InfiniiMax probe accessories.

Learn more about Oscilloscope Single-Ended Active Probes

Bandwidth:

• 3.5 GHz

Range:

• Dynamic Range: +/- 2.5V
• DC Offset Range: +/- 12V when using probe offset
• Maximum Voltage: +/- 30V

Input Impedance:

• Differential Input R: 50 kOhm
• Differential Input C: 0.27-0.34 pF
• Single Ended Input R: 25 kOhm
• Single Ended Input C: 0.44-0.67 pF

For high-speed differential or single-ended probing in embedded designs, the InfiniiMax 3.5 GHz 1131B differential probe amplifier is a perfect complement to Infiniium 2.5 to 3 GHz oscilloscopes. Its extremely low input capacitance, flat frequency response and patented resistor probe tip technology provide ultra-low loading of the DUT and superior signal fidelity. The InfiniiMax 1130B-34B Series supports a wide variety of real-world applications with an extensive line up of probe heads and accessories. The accessories can meet the most demanding mechanical access requirements.

The 1131B is the RoHS compliant version of the 1131A. The 1131B is 100% form, fit, function and price equivalent to the 1131A.

To see the other available probe head accessories for InfiniiMax 1130B-34B, visit InfiniiMax probe accessories.

Bandwidth:

• 1.5 GHz

Range:

• Dynamic Range: +/- 2.5V
• DC Offset Range: +/- 12V when using probe offset
• Maximum Input Voltage: 30V peak

Input Impedance:

• Differential Input R: 50 kOhm
• Differential Input C: 0.27-0.34 pF
• Single Ended Input R: 25 kOhm
• Single Ended Input C: 0.44-0.67 pF
   

For high-speed differential or single-ended probing in embedded designs, the InfiniiMax 1.5 GHz 1130B differential probe amplifier is a perfect complement to Infiniium 600 MHz to 1 GHz and InfiniiVision 500 MHz to 1 GHz oscilloscopes. Its extremely low input capacitance, flat frequency response and patented resistor probe tip technology provide ultra-low loading of the DUT and superior signal fidelity. The E2675B differential browser kit (ordered separately) is recommended for the 1130B with its variable spacing between probe tips with full z-axis compliance, which improves the usability/versatility of the probe. Also available are the E2669B differential or E2668B single-ended connectivity kits (ordered separately) that contain a variety of connectivity probe heads and accessories.

The 1130B is the RoHS compliant version of the 1130A. The 1130B is 100% form, fit, function and price equivalent to the 1130A.

To see the other available probe head accessories for InfiniiMax 1130B-34B, visit InfiniiMax probe accessories.

Bandwidth:

• 10 GHz

Range:

• Dynamic Range: 3.3 V peak-to-peak
• DC Offset Range: +/- 16V
• Maximum Voltage: +/- 30V

Input Impedance:

• Differential Input R: 50 kOhm
• Differential Input C: 0.21 pF
• Single Ended Input R: 25 kOhm
• Single Ended Input C: 0.35 pF

Recommended Probe Heads:

• MX0100A 25 GHz Micro Probe Head
• MX0106A 23 GHz Solder-in Probe Head
• MX0105A 20 GHz SMA Probe Head
• N2839A 21 GHz Browser Probe Head
• N5425B 18 GHz ZIF Probe Head
• N2851A 12 GHz QuickTip Probe Head
• E2678B 12 GHz Socketed Probe Head
• N5381B 12 GHz Solder-in Probe Head
• N5380B 12 GHz SMA Probe Head
• E2677B 12 GHz Solder-in Probe Head

Oscilloscope Connectivity:

• MXR, EXR oscilloscopes
• S-Series oscilloscopes
• 90000A oscilloscopes
• UXR 3.5mm oscilloscope with N5442A
• UXR 1&1.85mm oscilloscope with N5442A and N2852A adapters
• 90000X, Q, V, Z-series oscilloscopes with N5442A

The InfiniiMax II Series 1168B 10 GHz probing system for Infiniium oscilloscopes provides full real-time bandwidth to 10 GHz. The award-winning InfiniiMax probing system supports even the most demanding mechanical access requirements without sacrificing performance.

With only 3.4:1 of attenuation ratio, the 1168A/69A provides the lowest probe noise floor among InfiniiMax probes, making it ideal for signal integrity measurements that require high sensitivity. The 1168A/69A probe system supports a wide variety of real-world applications with an extensive line up of probe heads and accessories. Unrivaled InfiniiMax probe accessories support browsing, solder-in, socketed, ZIF tip, QuickTip (magnetic tip), soft touch head and SMA head solutions with various options to choose from.

The 1168B is the RoHS compliant version of the 1168A. The 1168B is 100% form, fit, function and price equivalent to the 1168A.

• Ampla largura de banda: CC a 50 MHz
• Alta relação S/N, capacidade de medição de correntes baixas
• 15 A de pico, 15 ACC, 10 Arms contínuo, 30 A de pico não contínuo
• Função de proteção contra entrada excessiva
• Chave de desmagnetização para remover qualquer magnetismo residual acumulado no núcleo magnético
• Compatível com a interface AutoProbe de alta impedância
• Para utilizar com as séries 80000 e 90000, use a ponta de prova de corrente N278xA com a fonte de alimentação N2779A e o adaptador de alta impedância E2697A
• Para utilizar com a série 90000X, use o adaptador de ponta de prova de alta impedância N5449A
   

A 1147B da Keysight é uma ponta de prova de corrente ativa, com ampla largura de banda, utilizada com os osciloscópios InfiniiVision e Infiniium.
A ponta de prova possui largura de banda plana (CC - 50 MHz), baixo ruído (<2,5 mA rms) e baixa perda de inserção de circuito.

A 1147B é ideal para captura de sinais de corrente transientes, tais como os encontrados em controladores de motor, fontes de alimentação de comutação, inversores e amplificadores de corrente, operando cargas indutivas.

A 1147B substitui a 1147A. A 1147A será descontinuada em junho de 2013 e terá 5 anos de suporte, até setembro de 2018. Os produtos substituintes são 100% equivalentes em formato, tamanho, função e preço aos produtos que substituem.

A ponta de prova para dispositivos montados em superfície 11060A da Keysight proporciona um método fácil para acessar e medir precisamente os dispositivos montados em superfície. A ponta de prova possui classificação de 3 A.

A 11060A da Keysight é compatível com os DMMs 34460A, 34461A, 34401A e 3458A da Keysight. Ela também pode ser utilizada com o 34420A da Keysight, porém, isso requer que a ponta de prova seja religada ao conector de entrada de baixo ruído 34104A da Keysight.

 

• Faixa de tensão: -42 V a 42 V
• Tensão máxima: 42 Vpico
• Terminação: 2 plugues banana simples
• Cabo: 384 fios de cobre com isolamento de borracha de silicone
• Comprimento: cabo é de 1,2 metro (48")

O kit 10072A é uma solução econômica para o teste de circuitos integrados com passo fino. Ele inclui dez clipes para CI e dois adaptadores com duas terminações, que conectam os clipes às pontas de prova da família 10070.

• Largura de banda: 500 MHz
• Tempo de subida do sistema (calculado): <700 ps
• Fator de atenuação: 10:1
• Resistência de entrada 2,2 MΩ (quando terminada em 1MOhm)

A ponta de prova passiva Keysight 10073D é a nossa ponta de prova de 500 MHz mais robusta, com uma fator de atenuação de 10:1 e alta impedância de entrada de 2,2 MΩ, ideal para uso geral. Ponta de prova passiva com ampla largura de banda para a série 6000 de 300 MHz - 1 GHz e osciloscópios das séries 7000, 8000 e 9000. A identificação da ponta de prova configura o osciloscópio automaticamente para a atenuação da ponta de prova.

Os seguintes acessórios estão inclusos: ponta retrátil em formato gancho; etiquetas de identificação nas cores laranja, branca, azul e verde; baioneta de aterramento; ponta para medição CI; ferramenta de ajuste e um terminal de aterramento com clipe jacaré.

• Largura de banda: 500 MHz
• Tempo de subida do sistema (calculado): <700 ps. fator de atenuação: 10:1
• Resistência de entrada: 2,2 MΩ (quando terminada em 1 MΩ)
• Capacitância de entrada: ~12pF
• Entrada máxima (CC + CA pico):
• Classificação de segurança: 500 V CAT I
• Categoria de segurança 300 V CAT II
• Razão de compensação: 6-15 pF
   

• O menor clipe para CI da indústria até hoje!
• Teste pacotes com tecnologia de montagem em superfície PQFP e SOIC com passo de 0,5 a 0,8 mm entre terminais
• Clipe com corpo fino que possibilita o posicionamento de vários, lado a lado

Esse clipes são os menores da indústria até a presente data e são ideais para conectar CIs com passo fino tão pequenos quanto 0,5 mm. O corpo do clipe permite que vários clipes sejam posicionados lado a lado. Cada kit inclui quatro clipes de 0,5 mm e dois adaptadores com terminação dupla.

O adaptador com terminação dupla facilita a conexão desses clipes à sua ponta de prova. Apenas insira a ponta da ponta de prova da família 10070 no adaptador. A terminação dupla do adaptador é para os clipes para CI ou para conectores com 0,635 mm de diâmetro.

• O menor clipe para CI da indústria até hoje!
• Teste pacotes com tecnologia de montagem em superfície PQFP e SOIC com passo de 0,5 a 0,8 mm entre terminais
• Clipe com corpo fino que possibilita o posicionamento de vários, lado a lado