Accessories

The 42941A Impedance Probe Kit used with the Impedance Analyzer provides the capability to perform in-circuit measurements (printed circuit patterns, the input/output impedance of circuits, etc.) with better accuracy and wider impedance coverage from 20 Hz to 120 MHz. In-circuit measurements can improve cycle time in a design environment, or reduce the cost of rework in a production environment.

Learn more about Keysight LCR Meter & Impedance Measurement Product Accessories

Frequency:
1 kHz to 1 GHz

Sample Size (Toroids Only):
height: ≤ 8.5 mm
inner diameter: ≥ 3.1 mm
outer diameter: ≤ 20 mm

The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.

For more information about Material Testing Equipment, please visit Materials Test Equipment and LCR Meter & Impedance Measurement Product Accessories

Frequency:
≤ 30 MHz

Measurement parameters:
capacitance (C), dissipation factor (D), and dielectric constant (εr', εr'')

Material-under-test size:
thickness: ≤ 10 mm
diameter: 10 to 56 mm

The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.

For more information about Material Testing Equipment, please visit Materials Test Equipment.

Learn more about LCR Meter & Impedance Measurement Product Accessories

 

Frequency:
1 MHz to 1 GHz

Sample size (smooth sheets only):
thickness: 0.3 mm to 3 mm
diameter: ≥ 15 mm

The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.

For more information about Material Testing Equipment, please visit Materials Test Equipment.

Learn more about LCR Meter & Impedance Measurement Product Accessories

The Keysight 41800A Active Probe provides high input impedance from 5 Hz to 500 MHz. The Keysight 41800A is a valuable tool when used with a network and spectrum analyzer for circuit signal analysis.

For more information about RF Probes, please visit Keysight RF Probes.

• Terminal Connector: 4-terminal pair, BNC
• Dimensions (approx.): 142(W) x 88(H) x 112(D) [mm] (capacitors)
• Weight (approx.): 7.0kg (including case and 3 capacitors)
• Applicable Instrument: E4980A, E4980AL, E4981A, E4990A

The 16380C is a standard capacitor set consisting of three precision capacitors - 0.01uF (16385A), 0.1uF (16386A), 1uF (16387A),and an optional 10uF (16388A). These capacitors are primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using these standards.

 

The 42942A terminal adapter converts the Impedance Analyzer four terminal-pair configuration into a 7 mm terminal configuration. As a result, test fixtures with a 7 mm terminal connector can be used with the Impedance Analyzer.
 

The 16200B test fixture is designed to operate with high frequency LCR meters and impedance analyzers. It allows you to supply a bias current across the device of up to 5 Adc through a 7 mm port by using an external DC current source.

• Measurement Instruments: 4192A, 4194A(Impedance Mode), 4263B, 4278A, 4279A, 4284A, 4285A, 4294A, E4980A
• Frequency: DC to 40MHz
• DC Bias:+/- 40V peak max (AC+DC)
• Operating Temperature: 0 to 55 degrees C
• Terminal Connection: BNC, 4 terminal-pair
• Dimensions(approx.): 128(W) x 60(H) x 71(D)mm
• SMD Test Fixture Selection Table

The 16034E test fixture is designed for impedance evaluations of SMD components. The minimum SMD size that this fixture is adapted to evaluate is 1.6(L) x 0.8(W) [mm].

Learn more about Keysight LCR Meter & Impedance Measurement Product Accessories
 

Soft carrying case with zipper for handheld digital multimeters.

Dimension: 9x5x3"

Keysight offer variety of accessories for digital multimeters, learn more about Keysight new digital multimeter accessories
 

Frequency

• Measurement Instrument: 4192A, 4194A (Impedance Mode), 4263B, 4278A, 4284A, 4285A and E4980A
• Frequency: 5Hz to 100kHz
• DC Bias: -42V to +42V
• Operating Temperature: 0 to 55degC
• How to use: Secure IC pins with clips
• Cable Length: Approx. 1m (from connector to tweezers tip)
• Terminal Connection: BNC, 4 terminal-pair

The 16089C makes it possible to measure odd-shaped components that cannot be measured with conventional fixtures. It is equipped with two insulated Kelvin clips.

Learn more about Keysight LCR Meter & Impedance Measurement Product Accessories

The 16065A test fixture makes it possible to measure a DUT with up to +/-200 V DC bias. The same modules of 16047A/D can be used to allow measurements of axial / radial lead components.