Accessories

• Maximum voltage: 42 V
• Termination: 5 single banana plugs (4-wire measurements plus ground)
• Length: cable is 0.8 meters (31.5 inches)

The Keysight kelvin probe set consists of two gold-plated flat tweezers with special gripping surfaces. This design assures a very precise contact to the component and very precise measurements. The ground guard connector removes ground-related errors. The gold plating helps to reduce the contact resistance between the surfaces of the test probe and the lead of the component being measured - reducing overall error!

The Keysight 11059A is compatible with the Keysight 34460A, 34461A, 34401A, 3458A, 34410A, 34411A, 34465A, 34470A digital multimeters and B2900 series precision source / measure units.

The bracket can be plugged into Keysight U1240 Series handheld digital multimeters to connect with the U1173A IR-USB cable.

• Termination: right-angle shrouded banana plugs
• Maximum current: 3 A
• Rating: 1000 V CAT II
• Length: 1.2 meters (48 inches)

The Keysight 34133A precision electronic test leads are designed specifically for working with small components and dense circuit boards. Each kit includes two test leads (one red and one black).

For more information about Keysight test leads and probes for multimeters, please visit Multimeter Test Leads and Probes.

The 34138A test lead set includes:

• test lead probes with retractable sheath (2)
• fine tip probes (2)
• SMT Grabbers (2)
• mini Grabber (1)

The Keysight 34138A test lead set for digital multimeters contains fixed sheath banana plugs.

The Keysight 34138A is compatible with the 34460A, 34461A, 34401A, 34405A, 34410A, 34411A, L4411A, and U2741A digital multimeters. The 34138a is not compatible with the 3458A instead use the 34137A with 3458A.

• termination: fixed sheath banana plugs
• length: 1.4 meters
• rating: 1000 V CAT II
• safety: IEC 61010-031

The U1186A consists of a thermocouple bead (K-type) and a mini connector to dual banana plugs.

The operating range for the thermocouple is from -20°C to 200°C.

Accuracy: ±1.1°C.

For more information about temperature measurement units, please visit Temperature Sensors and Temperature Probes.

• Maximum baud rate: 19,200 bits per second
• For remote control and data logging to PC
• Operating temperature: 0 - 50°C
• NEW: Support Windows 10

The Keysight U1173B IR - USB PC connectivity cable is compatible with the U1210, U1230, U1240, U1250, U1270 and U1280 series handheld digital multimeters.

For U1240 series, an additional U1179A IR connectivity bracket is required.

Keysight offer variety of accessories for digital multimeters, learn more about Keysight new digital multimeter accessories

• Test leads: CAT III 1000V, CAT IV 600V, 15A rating
• Test probe (19-mm tips): CAT II 1000V, 15A rating
• Test probe (4-mm tips): CAT III 1000V, CAT IV 600V, 15A rating (highly recommended for CAT IV environment) Alligator Clips: Cat III 1000V, CAT IV 600V, 15A rating
• Fine Tip Test Probes: Cat II 300V, 3A
• SMT Grabber: Cat II 300V, 3A
• Mini Grabber (black only): Cat II 300V, 3A

The Keysight U1168A standard test lead kit is compatible with the U1230, U1240, U1250 and U1270 Series handheld digital multimeters. The set includes one pair of test leads, test probes (19-mm tips), test probes (4-mm tips), alligator clips, fine tip test probes, SMT Grabbers and mini grabber ( black only).

For more information about Keysight test leads and probes for multimeters, please visit Multimeter Test Leads and Probes.

• Remote switch and adapter – CAT III 1000 V / CAT IV 600 V, 15 A (highly recommended for CAT IV environment)
• 18 mm test probes – CAT II 1000 V, 15 A
• 4 mm test probes (with conversion cap) – CAT III 1000 V / CAT IV 600 V, 15 A
   

U5404A remote switch probe is compatible with Keysight U1281A / U1282A handheld DMMs.

Keysight offer variety of accessories for digital multimeters, learn more about Keysight new digital multimeter accessories

• K-type bead probe supplied.
• Measures -50°C ~ 1000°C / -58°F ~ 1832°F.
• Slider switch to measure in °C or °F.
• 1 mV/°C or 1mV/°F output.
• Either Alkaline or Carbon-Zinc single standard 9V battery needed.
• To be used with Keysight handheld oscilloscopes or handheld digital multimeters.
  

The U1586B temperature adapter expands the capabilities of your handheld oscilloscope or handheld digital multimeter to measure temperature, either in °C of °F. To be used with a K-type bead thermocouple, and with approximately 1600 hours battery life with an alkaline battery, this adapter ensures you get the most out of your handheld scope or DMM purchase.

The U1164A consists of one pair (red and black) of fine tip probes. Recommended for with Keysight standard test leads.

The probes are rated at CAT II 300V, 3A.

Compatible with test leads shipped together with Keysight U1210, U1240B, U1250, U1270 series of handheld clamp meter and multimeter.

For more information about Keysight test leads and probes for multimeters, please visit Multimeter Test Leads and Probes.

• Short: #24 AWG plated copper wire
• Terminals: low-thermal copper alloys
• Termination: five shrouded banana plugs
• Quantity: 2

The Keysight 34172B digital multimeter calibration short is a set of two shorts which provide a convenient and reliable method to apply a short to the input connectors of the multimeter. Terminals are made of low-thermal copper alloys to minimize thermally-induced voltages caused by dissimilar metals.

The Keysight 34172A is compatible with the Keysight 34460A, 34461A, 34401A, 34410A, 34411A, and L4411A digital multimeters.

• Wire: #22 to #28 AWG recommended
• Termination: 34420A mating connector

The Keysight 34104A is a low-thermal input connector that mates with the 34420A. It allows a user to design custom input connections.

The Keysight 34104A is only compatible with the 34420A.