Designing for Modulation with Keysight EDA

Learn about the 8 great reasons why you use Keysight's EDA software to design with modulation.

Reducing Cost & Risk with Inspector Pre-Silicon Side Channel Analysis

Learn why detecting and analyzing side‑channel leakage early in the design cycle using Inspector Pre‑Silicon helps reduce cost and risk down the road. This webinar shows how simulation‑based SCA uncovers where and when leakage occurs, helps validate countermeasures, reduces costly redesigns, and strengthens chip‑level security before tape‑out.

AI/ML Algorithm Design and Testing Toward 6G

This webinar examines how AI and machine learning are transforming wireless communications, with a focus on design, validation, and measurement challenges. Learn how AI/ML enhances signal processing and network performance while ensuring accuracy, reliability, and scalability. Gain practical strategies and real-world insights to address testing complexities and advance next-generation wireless systems.

Coexistence Testing for Wireless Medical Devices

This webinar explores how to design and validate wireless coexistence for connected medical devices in increasingly crowded RF environments. Learn how to identify vulnerabilities early, simulate real-world conditions, and mitigate interference risks. The session also covers key standards such as ANSI C63.27 and AAMI TIR 69, with practical strategies to ensure reliable device performance and protect patient safety in modern healthcare settings.

Automated Wireless Coexistence Testing Using ANSI C63.27

This webinar outlines how automated wireless coexistence testing enables consistent, repeatable validation of medical devices against ANSI C63.27. It highlights structured workflows that support early risk identification, reduce manual effort, and guide Tier 1, Tier 2, and Tier 3 testing. The session includes a demonstration of the Keysight Wireless Coexistence Test Solution in a lab setting to support design confidence and regulatory readiness.

How to test a DC-DC converter using DAQ and BenchVue

Watch this video to learn how easy it is to test a DC-to-DC converter using PathWave BenchVue software and data acquisition system hardware. The PathWave BenchVue software helps you configure, intuitively control multiple instruments, and automate your test sequences quickly and with minimal instrument knowledge.

Acoustic Measurement Using a Dynamic Data Acquisition System

This video shows how easy it is to set up the hardware and software to make acoustic measurements quickly using Keysight PathWave BenchVue software and DAQ hardware to display and enable post-analysis work.

Introducing the PZ2100 High-Channel Density Precision SMU Solution (Without Sub-title)

Learn how the new PZ2100 SMU solution helps you overcome 5 key challenges testing low-power integrated circuits, and how it enables you to focus more of your time in testing, rather than implementation details.

Grid-Edge Frontier – Implications and Opportunities for the E-Mobility Industry

The increasing number of electric vehicles (EVs) being used as intelligent distributed energy resources (DERs) offers an exciting opportunity for EV and EV supply equipment (EVSE) manufacturers to differentiate their products in the market. With the global adoption of bidirectional EV charging, and the addition of vehicle-to-grid (V2G) services, the EV battery pack goes from being just a consumer product that powers the vehicle, to being able to supply electricity back to the grid. Energy providers (utilities) around the world enforce very strict rules and standard test requirements around DERs and their interconnection and interoperability with the grid. The various global EV charging standards make it even more complicated for EV and EVSE manufacturers to ensure global compliance of interconnection with the local grid. Join our panel of experts, who will dive into the design and test challenges posed by evolving V2G standards, and ways to solve these challenges.

Battery Design for Electric Vehicles

Growth in the electric vehicle (EV) market is fueling demand for better batteries that can address drivers' range anxiety, while enabling fast charging. For battery developers, the goal is to design safe batteries with high energy and power density, in addition to optimizing battery costs. This panel of industry experts will discuss advances in battery development for the EV market, and battery test requirements from cell, to module, and pack, to enable the design of better batteries.

Improve Battery Cell Cycling and Reduce Gigafactory Cost

Gigafactories produce battery cells at high volumes to support the demand for electric vehicle (EV) batteries. To meet quality standards, each cell undergoes careful measurement during the manufacturing process. However, it’s not possible to obtain an accurate read on a cell’s cycle life due to the sheer quantities of cells, hence manufacturers carry out sampling measurements. This webcast presents a case study on how a major cell manufacturer implements its cell cycling quality gate at its gigafactory. It discusses considerations such as capital equipment, floor space, safety and energy consumption, and data analysis.

Ask the Experts High Density Precision SMU

Whether you are an experienced engineer seeking to optimize your testing processes or a newcomer aiming to understand the intricacies of high-density precision SMU testing, this webinar is designed to equip you with the knowledge needed to make informed decisions and achieve accurate results in your testing endeavors. Join us as we unravel the complexities, provide expert guidance, and answer your top questions in the realm of high-density precision SMU testing.

Unlocking V2G: Opportunities and Challenges for EV Integration

Uncover the exciting development vehicle-to-grid (V2G) technologies and essential testing practices for compliance and interoperability. Keysight experts will also demo the latest anti-islanding test solutions to meet the IEEE 1547.1-2020 / UL 1741 SB requirements.

Revolutionize Spacecraft Power System Design with Hardware-in-the-Loop Testing

Discover in this webinar how the integration of digital twin technology and hardware in the loop simulation with Keysight's power supply technology can revolutionize your spacecraft projects.

Lab administrator feature - Demo Video

Introduction of Lab administrator feature to allow lab admin to monitor the lab instrument connection status

5G Beam-Steering with EM/Circuit Excitation and Co-simulation in PathWave ADS

This video shows how EM/Circuit excitation and co-simulation in PathWave Advanced Design System (ADS) allows you to combine the whole transmit chain with all of its circuit level components along with the physical antenna's EM simulation to deliver accurate simulation results of the whole system with all of its components, including the antenna.

How to Design DC-to-DC Converters

This video introduces basic DC-to-DC converter operation, explains why voltage spikes occur in these circuits, and shows the importance of modeling PC board layout effects. There is an example in which current visualization is used to see potential problem areas in the PC board. The layout is then modified to improve performance.

IxLoad 9.00 - GRE

Demo of how to use GRE to tunnel IPv6 traffic over IPv4 networks.

How to measure CV Load regulation on a DC Power Supply

Testing the CV regulation of a power supply using an N3300 electronic load to draw a constant current. A multimeter is used to measure the small change in voltage.

Using N7611B Signal Studio Software for Sirius XM Radio

Demo on testing Sirius XM broadcast radio using the N7611B signal studio software. Learn more about automotive test challenges and solutions with resources from Keysight.