All Software Catalog

• Intuitive setup wizard for quick test setup, configuration, and test.
• Powerful characterization through multiple trials that show a full array of statistics for each measurement and returns the worst measurement value.
• Comprehensive test coverage of the GDDR7 electrical, timing, eye diagram and jitter tests.
• Offline testing capability with waveform files for completeness of simulation to validation workflow.
• De-embed interposer, cable and even package models to verify the true device performance.
• Cutting-edge equalization emulation using Keysight's built-in equalization analysis, including auto tap setup with multiple optimization algorithms, to accurately determine and simulate ideal DFE settings for a trained GDDR7 memory system.
• Signal-to-Noise and Distortion Ratio (SNDR) measurements to evaluate PAM signaling performance in the presence of crosstalk and other system impairment sources

The KS2201A PathWave Test Sync Executive is a programming environment based on Keysight's Hard Virtual Instrument (HVI) technology, that enables the development and execution of synchronous, real-time operations across multiple instruments. The real-time sequencing and synchronization capabilities make it a breakthrough tool for developing measurement applications that require tight synchronization, phase coherence, and real-time control and feedback. Achieve rapid development of high performance, synchronous real-time solutions with transparent multi-instrument synchronization.

Typical Testing Applications

• Quantum research: Instrumented Qubit control systems
• Multi-channel comms: MIMO, beamforming, multi-emitter test
• Wireless Power Amplifier (PA) test: alignment of envelope tracking (ET) and digital pre-distortion (DPD)
• Electronic Warfare (EW): Precisely timed multi-emitter and beamformed A/D systems
• Other validation applications that require precise timing across multiple chasses and families of equipment. (note: equipment support is also required)

Automotive Ethernet Conformance Test Software for a High Performance Oscilloscope

Next-generation ADAS systems require camera and radar systems with increasingly high resolution. That means new requirements for speed and bandwidth. The Automotive Ethernet standard enables faster data communication to meet the demands of today’s vehicles and the connected vehicles of the future.

Unlike CAN, LIN, Automotive Ethernet demands rigorous compliance verification using test cases that cover transmitters (Tx), receivers (Rx), and harness/connector assemblies. To help you save time and effort, Keysight offers solutions that automate the testing and validation across Transmitter (Tx), Receiver (Rx), and the connections between Automotive Ethernet devices. Our engineers have invested thousands of hours in learning the standards and creating automated, repeatable compliance tests. These proven applications help you ensure proper test configuration and valid measurement results. Ultimately, you’ll have greater confidence that your device is compliant. Now available for data rates up to 10Gbps. The AE6000T Automotive Ethernet Test Solution offers hardware and accessories to make sure you have all of the components you need to get up and running quickly.

The AE6920T Automotive Ethernet Tx Compliance Software covers 2 standards and 6 data rates in one solution:

• IEEE 10BASE-T1S, 100BASE-T1,1000BASE-T1, 2.5GBASE-T1, 5GBASE-T1 and 10GBASE-T1
• OPEN Alliance TC14, TC1, TC8, TC12, TC15

Key Capabilities

• Automated set up ensures result repeatability
• Test setup wizard guides you through test selection, configuration, connection, execution, and results reporting
• Comprehensive reports give you the test configuration, measurements made, pass / fail status, margin analysis, and waveforms
• Perform repeatable results with Keysight oscilloscopes

Ordering Information

• Software licenses are available either as node-locked, transportable, USB, or floating
• Licenses are available for purchase with 6-, 12-, 24- or 36-month support
• Software supports Infinium UXR-Series oscilloscopes

Interoperable and failure-free Automotive Ethernet multiGBASE-T1 devices are the goal — receiver testing can help.

Ensuring the receiver component of an Automotive Ethernet module or switch meets signal-quality requirements, is interoperable with others in the system, and complies with the IEEE 802.3ch Automotive Ethernet standard requires physical-layer electrical tests.

• OFDM, FBMC, F-OFDM with SCMA/NOMA multiple access
• FDD/TDD modes, up to 65,539 subcarriers
• Modulation formats from BPSK QPSK, 16 QAM to 1024QAM, 8PSK or uder-defined
• Support Massive MIMO & Beamforming up to 64 channel for 6G research
• EVM, constellation, burst summary, spectrum and more
• Multiple, simultaneous color-coded result views
• Provide the preset for wireless standards such as 6G Radio (FR1 and FR3 TDD), 5G NR (FR1 FDD/TDD), WLAN (802.11a/ah), ISDB-T, DAB, DVB-SH, and DVB-T/H, and more
• Improve EVM measurment with cross-correlated EVM (ccEVM) or IQ noise correction (IQ-NC) technoligies (requires 89601EVMC license)

Comprehensive measurement and debug solution

• Provides rapid and automated testing of 100 Gb/s over four lanes on Ethernet network devices
• Automates compliance test coverage for tests in the IEEE P802.3bj Clause 93 transmitter electrical specification
• Test setup wizard guides user through test selection, configuration, connection, execution and results reporting

Flexible and extensible

• Operates on the Keysight Z-Series and UXR real-time oscilloscopes
• Automatic HTML report generation
• Test all or selected parameters to compliance limits or custom limits

Compatibility

• Z-Series and UXR real-time oscilloscopes 

The D9010BJBC 100GBASE-KR4 compliance test application software for Infiniium Series oscilloscopes gives you a fast and easy way to verify and debug your 100 Gb/s backplane Ethernet designs. The Ethernet compliance software lets you automatically execute Ethernet physical-layer (PHY) electrical tests, and it displays the results in a flexible report format. In addition to the measurement data, the report provides a margin analysis that shows how closely your device passed or failed each test.

The Keysight D9010BJBC 100GBASE-KR4 compliance test application software for Infiniium Series oscilloscopes performs a wide range of electrical tests to meet the IEEE P802.3bj Clause 93 electrical specifications.

The D9010BJBC 100GBASE-KR4 compliance test application software runs on Z-Series and UXR oscilloscopes.

Performing these tests gives you confidence in your design. The D9010BJBC 100GBASE-KR4 compliance test application software helps you execute a wide subset of the compliance tests using an oscilloscope, spectrum analyzer and vector network analyzer. The test application offers a user-friendly setup wizard and a comprehensive report that includes margin analysis.

Comprehensive Measurement And Debug Solution

• The D9010EAPC 10GBASE-KR Backplane Ethernet electrical compliance application software provides rapid and automated testing of Backplane Ethernet network devices
• The application automates compliance test coverage for tests in the Backplane Ethernet IEEE 802.3ap specification
• A wide range of 10GBASE-KR Backplane Ethernet electrical tests are performed

Flexible And Extensible

• Automated setup ensures result repeatability and let’s test engineers run the application without being an expert on Backplane Ethernet testing procedures
• Test setup wizard guides user through test selection, configuration, connection, execution and results reporting
• Oscilloscope setup is automatically configured for each test, and measurement connection setups are displayed
• Test results reports test configuration, measurements made, pass/fail status, margin analysis and waveforms

Compatibility

• Z-Series and UXR real-time oscilloscopes

The D9010EAPC 10GBASE-KR Backplane Ethernet electrical performance validation and compliance software for Infiniium Series oscilloscopes gives you a fast and easy way to verify and debug your 10GBASE-KR and 40GBASE-KR4 Ethernet designs. The Ethernet electrical test software lets you automatically execute Ethernet physical-layer (PHY) electrical tests and displays the results in a flexible report format. In addition to the measurement data, the report provides a margin analysis that shows how closely your device passed or failed each test.

The 10GBASE-KR electrical performance validation and compliance software performs a wide range of electrical tests to meet the 10GBASE-KR electrical specifications as documented in the IEEE 802.3ap standard. The software requires at least one InfiniiMax active differential probe (N2802A or N2803A) with N2836A InfiniiMax III 26 GHz solder-in probe head.

The D9010EAPC 10GBASE-KR Backplane Ethernet electrical performance validation and compliance software runs on all Infiniium Z-Series and UXR oscilloscopes.

Comprehensive measurement and debug solution

• Provides rapid and automated testing of 10 Gb/s over four lanes on Ethernet network devices
• Automates compliance test coverage for tests in the IEEE P802.3bj Clause 85 transmitter electrical specification
• Optional Ethernet compliance testing is supported using the Keysight switch matrix hardware

Flexible and extensible

• Operates on the Keysight Z-Series and UXR real-time oscilloscopes
• Automatic HTML report generation
• Test all or selected parameters to compliance limits or custom limits

Compatibility 

• Z-Series and UXR real-time oscilloscopes

The D9010BJAC 40GBASE-CR4 and 100GBASE-CR10 compliance test application software for Infiniium Series oscilloscopes gives you a fast and easy way to verify and debug your 10 Gb/s copper Ethernet designs. The Ethernet compliance software lets you automatically execute Ethernet physical-layer (PHY) electrical tests, and it displays the results in a flexible report format. In addition to the measurement data, the report provides a margin analysis that shows how closely your device passed or failed each test.

The Keysight D9010BJAC 40GBASE-CR4 and 100GBASE-CR10 compliance test application software for Infiniium Series oscilloscopes performs a wide range of electrical tests to meet the IEEE P802.3bj Clause 85 electrical specifications.

The D9010BJAC 40GBASE-CR4 and 100GBASE-CR10 compliance test application software run on Z-Series and UXR oscilloscopes.

Performing these tests gives you confidence in your design. The D9010BJAC 40GBASE-CR4 and 100GBASE-CR10 compliance test application software helps you execute a wide subset of the compliance tests using an oscilloscope, spectrum analyzer and vector network analyzer. The test application offers a user-friendly setup wizard and a comprehensive report that includes margin analysis.

• The fastest throughput oscilloscope solution for triggering on and analyzing automotive serial buses using hardware-based architecture
• On-screen serial decode time-correlated with the serial data waveform
• CAN eye-diagram mask testing - easily download multi-region masks and setups based on industry standards
• Detailed pass / fail statistics from mask tests
• This package enables CAN and LIN serial trigger and decode, along with pass / fail mask limit testing

The automotive software package for Keysight’s InfiniiVision 2000 X-Series oscilloscopes enables protocol triggering and decode for a broad range of the most common automotive serial buses used today for power train and body control and monitoring. This package also enables hardware-based pass / fail mask limit testing.