Accessories

• Test and validate high-speed technologies such as DDR5 / MIPI with the 25 GHz probe amplifier (AP2).
• Experience the highest input impedance in midband frequencies for low-energy probing.
  
• Boost test margins with the lowest signal degradation.
• Probe small devices with the super-flexible micro probe head or choose from the widest variety of compatible probe heads for your unique application.
• Measure differential, single-ended, and common mode signals with a single probe tip.
  
• Use with Infiniium UXR-, 90000 X-, Q-, V-, and Z-Series oscilloscopes.

Keysight’s MX0025A InfiniiMax Ultra Series probe amplifier improves usability because you can measure differential, single-ended, and common mode signals with a single probe tip.

When you use a probe to connect your signal to your oscilloscope, it becomes part of the circuit affecting your test. Your probe may be hiding signal details, loading down your signal, or distorting it. InfiniiMax Ultra Series probes have the lowest loading for minimal impact to your circuit. Boost your test margins and gain measurement confidence with their unprecedented accuracy. Ensure your entire measurement system is helping you see the truest representation of your signal.

These probes have the lowest noise and capacitive loading and the lowest loading across more frequencies due to their RC high impedance profile. The InfiniiMax Ultra Series supports InfiniiMode and has a user-defined AC calibration mode, a wider input voltage range, more accuracy with unique S-parameter characterization, lower capacitive loading, a wider input voltage range, micro / socketed probe heads for smaller density probing, and more bandwidths. The InfiniiMax Ultra Series has an RC input impedance architecture with the lowest loading and least signal distortion across the widest frequency range.

InfiniiMax Ultra probes have three attenuation ranges — 1:1, 4:1, and 8:1 — giving you superior noise performance and large voltage ranges, all while maintaining maximum bandwidth. The input range automatically configures depending on the size of the input signal and vertical scale of your oscilloscope.

Choose from the three flexible input dynamic ranges from 600 mVpp at 1:1, 2.5 Vpp at 4:1, and 5 Vpp at 8:1. Clearly see and know when your design is satisfactory, keep up with standards, easily probe small devices, and reduce test complexity with the InfiniiMax Ultra Series probes.

• Module plugs into rear-panel expansion slot
• Combines 10/100Mbit LAN port with VGA out
• LAN port is LXI compliant, enabling remote access, command, and printing
• Compatible with VNC viewer for secure access
• Web browser-based interface allows remote control -- ideal for accessing remote R&D and teaching labs.

LAN/VGA module gives you network connectivity and complete LXI compliant support as well as the ability to connect to an external monitor. Operate your scope remotely from your PC using the web browser interface with the virtual front panel interface that looks and acts as the real front panel on the scope with the same associated keys and knobs. Oscilloscope are required.

Bandwidth:

• Bandwidth: 7 GHz

Range:

• Dynamic Range: +/- 2.5V
• DC Offset Range: +/- 12V when using probe offset
• Maximum Voltage: +/- 30V

Input Impedance:

• Differential Input R: 50 kOhm
• Differential Input C: 0.27-0.34 pF
• Single Ended Input R: 25 kOhm
• Single Ended Input C: 0.44-0.67 pF

For high-speed differential or single-ended probing in embedded designs, the InfiniiMax 7 GHz 1134B differential probe amplifier is a perfect complement to Infiniium 6 GHz oscilloscopes. Its extremely low input capacitance, flat frequency response and resistor probe tip technology provide ultra-low loading of the DUT and superior signal fidelity. The InfiniiMax 1130B-34B Series supports a wide variety of real-world applications with an extensive line up of probe heads and accessories. The accessories can meet the most demanding mechanical access requirements.

The 1134B is the RoHS compliant version of the 1134A. The 1134B is 100% form, fit, function and price equivalent to the 1134A.

To see the other available probe head accessories for InfiniiMax 1130B-34B, visit InfiniiMax probe accessories.

Learn more about Oscilloscope Single-Ended Active Probes

The Keysight 1180CZ testmobile scope cart provides convenient mobility of test equipment to make them readily available when needed and effectively extend the amount of lab bench space. The 1180CZ allows several operators to cost effectively share expensive equipment.

• Ergonomic design - test equipment is operator-accessible whether seated or standing
• Heavy-duty casters make moving instruments easy
• Includes a steel buckle and nylon strap to secure instruments to the cart
• Attractive quartz gray color
• Tilt tray adjusts 30-plus degrees for viewing comfort
• Material: Cold-rolled steel
• Weight: 25.9 kg (57 lb)
• Casters: 101 mm (4 in) diameter
• Tilt Tray Load Capacity: 29.5 kg (65 lb)
• Total Load Capacity: 59 kg (130 lb)
• Tilt Tray Width: 457 mm (18 in)
• Tilt Tray Depth: 457 mm (18 in)

• Lower bandpass cutoff frequency: 3.2 kHz
• Center bandpass frequency: 50 kHz
• Upper cutoff frequency: 800 kHz
• Maximum input voltage: 10 V_PP into 50 Ω
• Probe test points: V_IN, BPF_OUT, LPF_OUT, GND (2X)
• Series component values: R = 50 Ω, L = 10 µH, C = 1 µF

Note: All specifications stated as typical.

The DSOXBODE Bode plot training kit consists of a series R-L-C circuit board with a BNC input that attaches directly to the output of the oscilloscope’s WaveGen function generator. There are clearly labeled test points for probing V_IN and BPF_OUT (bandpass filter output) or LPF_OUT (low-pass filter output). Also included with this training kit is a comprehensive tutorial and lab guide that engineering students and professors can download.

For limited time, get a free DSOXBODE Bode plot training kit with the purchase of each InfiniiVision 1000 X-Series oscilloscope with the built-in waveform generator (EDUX1052G, DSOX1202G, and DSOX1204G models only)

Click on the Document Library tab to download the DSOXBODE Tutorial & Lab Guide document.

Bandwidth:

• 5 GHz

Range:

• Dynamic Range: +/- 2.5V
• DC Offset Range: +/- 12V when using probe offset
• Maximum Voltage: +/- 30V

Input Impedance:

• Differential Input R: 50 kOhm
• Differential Input C: 0.27-0.34 pF
• Single Ended Input R: 25 kOhm
• Single Ended Input C: 0.44-0.67 pF

For high-speed differential or single-ended probing in embedded designs, the InfiniiMax 5 GHz 1132B differential probe amplifier is a perfect complement to Infiniium 4 GHz oscilloscopes. Its extremely low input capacitance, flat frequency response and patented resistor probe tip technology provide ultra-low loading of the DUT and superior signal fidelity. The InfiniiMax 1130B-34B Series supports a wide variety of real-world applications with an extensive line up of probe heads and accessories. The accessories can meet the most demanding mechanical access requirements.

The 1132B is the RoHS compliant version of the 1132A. The 1132B is 100% form, fit, function and price equivalent to the 1132A.

To see the other available probe head accessories for InfiniiMax 1130B-34B, visit InfiniiMax probe accessories.

Learn more about Oscilloscope Single-Ended Active Probes

Bandwidth:

• 3.5 GHz

Range:

• Dynamic Range: +/- 2.5V
• DC Offset Range: +/- 12V when using probe offset
• Maximum Voltage: +/- 30V

Input Impedance:

• Differential Input R: 50 kOhm
• Differential Input C: 0.27-0.34 pF
• Single Ended Input R: 25 kOhm
• Single Ended Input C: 0.44-0.67 pF

For high-speed differential or single-ended probing in embedded designs, the InfiniiMax 3.5 GHz 1131B differential probe amplifier is a perfect complement to Infiniium 2.5 to 3 GHz oscilloscopes. Its extremely low input capacitance, flat frequency response and patented resistor probe tip technology provide ultra-low loading of the DUT and superior signal fidelity. The InfiniiMax 1130B-34B Series supports a wide variety of real-world applications with an extensive line up of probe heads and accessories. The accessories can meet the most demanding mechanical access requirements.

The 1131B is the RoHS compliant version of the 1131A. The 1131B is 100% form, fit, function and price equivalent to the 1131A.

To see the other available probe head accessories for InfiniiMax 1130B-34B, visit InfiniiMax probe accessories.

Bandwidth:

• 1.5 GHz

Range:

• Dynamic Range: +/- 2.5V
• DC Offset Range: +/- 12V when using probe offset
• Maximum Input Voltage: 30V peak

Input Impedance:

• Differential Input R: 50 kOhm
• Differential Input C: 0.27-0.34 pF
• Single Ended Input R: 25 kOhm
• Single Ended Input C: 0.44-0.67 pF
   

For high-speed differential or single-ended probing in embedded designs, the InfiniiMax 1.5 GHz 1130B differential probe amplifier is a perfect complement to Infiniium 600 MHz to 1 GHz and InfiniiVision 500 MHz to 1 GHz oscilloscopes. Its extremely low input capacitance, flat frequency response and patented resistor probe tip technology provide ultra-low loading of the DUT and superior signal fidelity. The E2675B differential browser kit (ordered separately) is recommended for the 1130B with its variable spacing between probe tips with full z-axis compliance, which improves the usability/versatility of the probe. Also available are the E2669B differential or E2668B single-ended connectivity kits (ordered separately) that contain a variety of connectivity probe heads and accessories.

The 1130B is the RoHS compliant version of the 1130A. The 1130B is 100% form, fit, function and price equivalent to the 1130A.

To see the other available probe head accessories for InfiniiMax 1130B-34B, visit InfiniiMax probe accessories.

Bandwidth:

• 10 GHz

Range:

• Dynamic Range: 3.3 V peak-to-peak
• DC Offset Range: +/- 16V
• Maximum Voltage: +/- 30V

Input Impedance:

• Differential Input R: 50 kOhm
• Differential Input C: 0.21 pF
• Single Ended Input R: 25 kOhm
• Single Ended Input C: 0.35 pF

Recommended Probe Heads:

• MX0100A 25 GHz Micro Probe Head
• MX0106A 23 GHz Solder-in Probe Head
• MX0105A 20 GHz SMA Probe Head
• N2839A 21 GHz Browser Probe Head
• N5425B 18 GHz ZIF Probe Head
• N2851A 12 GHz QuickTip Probe Head
• E2678B 12 GHz Socketed Probe Head
• N5381B 12 GHz Solder-in Probe Head
• N5380B 12 GHz SMA Probe Head
• E2677B 12 GHz Solder-in Probe Head

Oscilloscope Connectivity:

• MXR, EXR oscilloscopes
• S-Series oscilloscopes
• 90000A oscilloscopes
• UXR 3.5mm oscilloscope with N5442A
• UXR 1&1.85mm oscilloscope with N5442A and N2852A adapters
• 90000X, Q, V, Z-series oscilloscopes with N5442A

The InfiniiMax II Series 1168B 10 GHz probing system for Infiniium oscilloscopes provides full real-time bandwidth to 10 GHz. The award-winning InfiniiMax probing system supports even the most demanding mechanical access requirements without sacrificing performance.

With only 3.4:1 of attenuation ratio, the 1168A/69A provides the lowest probe noise floor among InfiniiMax probes, making it ideal for signal integrity measurements that require high sensitivity. The 1168A/69A probe system supports a wide variety of real-world applications with an extensive line up of probe heads and accessories. Unrivaled InfiniiMax probe accessories support browsing, solder-in, socketed, ZIF tip, QuickTip (magnetic tip), soft touch head and SMA head solutions with various options to choose from.

The 1168B is the RoHS compliant version of the 1168A. The 1168B is 100% form, fit, function and price equivalent to the 1168A.

• Wide bandwidth: DC to 50 MHz
• High S/N ratio, low current measurement capability
• 15A peak, 15 ADC, 10 Arms continuous, 30A peak non-continuous
• Easy protect function at excessive input
• Demagnetizing switch to remove any residual magnetism that builds up in the magnetic core
• Compatible with high impedance AutoProbe interface
• For use with 80000/90000 Series, use N278xA current probe with N2779A power supply and E2697A high impedance adapter
• For use with 90000 X-Series, use the N5449A high impedance probe adapter

The Keysight 1147B is a wide bandwidth, active current probe for InfiniiVision and Infiniium oscilloscopes.

The probe features flat bandwidth (DC-50 MHz), low noise (<2.5 mA rms) and low circuit insertion loss.
 

The 1147B is ideal for capturing transient current signals such as those found in motor controllers, switching power supplies, inverters and current amplifiers driving inductive loads.

The 1147B is the replacement of the 1147A. The 1147A is now discontinued. The 1147B is 100% form, fit, function and price equivalent to the 1147A.

• 400 MHz bandwidth
• 2,000 Vrms mains isolated, 6,000 V transient overvoltage
• Attenuation ratios: 50:1, 100:1, 250:1 or 500:1, auto-switchable on Infiniium scope
• Differential input impedance: 10 MΩ || 2pF
• High CMRR simplifies the measurement challenges found in noisy, high common-mode power electronics environments.
• UL safety certified
• Comes with a wide variety of high quality accessories
• AutoProbe interface, 50 Ω input

The DP0001A is a 400 MHz high voltage differential probe with 2 kV mains isolated or 1 kV CAT III rating designed for making accurate high-voltage power measurements required for testing today’s WBG power devices, power converters or motor drives. Thanks to high bandwidth and low loading characteristics, the probe can accurately measure 1kV transient pulse with as fast as 1.2 nsec of edge speed (10-90%) in modern switching power supplies. Also, high CMRR simplifies the measurement challenges found in noisy, high common-mode power electronics environments.

When used with an Infiniium oscilloscope, the probe supports an auto-switchable attenuation ratio that automatically sets the probe attenuation to the value necessary to make the dynamic range of the probe greater than or equal to the level required to measure the current input signal. A variety of accessories are shipped with this probe to suit various DUT connection scenarios and to make the connection to compact target devices possible.

The differential probes have a differential input resistance of 10 MΩ and low input capacitance of 2 pF to minimize circuit loading. The DP0001A is compatible with Keysight oscilloscopes with a 50-Ω AutoProbe interface, which configures the scope for the probe automatically.
When probing differential signals inside of environmental chambers at extreme temperatures, Keysight offers the N7013A extreme temperature extension kit. The N7013A is compatible with the DP0001A with a de-rated bandwidth of 70 MHz. The 70 cm long differential cable set and accessories can operate in temperatures ranging from -40 degC to +85 degC.

The probe is compatible with InfiniiVision 3000TX, 4000X, 6000X and Infiniium S, 9000A, 90000X, V, Z, UXR <=33GHz (with N5442A adapter).

• Easy connection to surface mount ICs
• Safe, with no chance of shorting
• Mechanically non-invasive contact
• Operating voltage: less than 40 V (dc + peak ac)
• Operating current: 0.5 A maximum
• Capacitance between contacts: 4.3 pF at 1 MHz
• Self-inductance: 37 nH at 1 MHz
• Contact resistance: less than 0.1 Ohm

The Keysight E2644A is a wedge probe adapter. If you've ever tried to probe a surface mount component, you've probably experienced one or more of the following frustrating situations: accidentally shorting IC pins together; electrical and/or mechanical problems with soldering small wires onto leads; and/or holding multiple probes and trying to use your scope at the same time. The Keysight Wedge Probe Adapter provides a solution to these frustrations.

It is easy to insert and stays put - no need to solder small wires onto leads. The Wedge is mechanically non-invasive, so you won't damage the legs of the IC. It makes two contact points with each leg of the IC. This redundant physical connection increases the electrical reliability of the connection.