Accessories

The RP7909A rack mount kit makes it easy to integrate a 5kW or 10 kW RP7900 Series regenerative power system into a 19-inch EIA rack cabinet. This rack mount kit includes slide rails, and flange mounts (without ears).

This rack mount kit is compatible with the following models: RP7931A - RP7963A.

Extend your Charging Discovery System for EV-side MCS testing

The SL2640A Add-on Box extends the Charging Discovery System with an instrumented MCS charging cable and connector interface for EV-side testing. It supports development, interoperability, and performance validation of MCS-enabled electric vehicles and charging controllers. Engineers can perform communication-only testing during early development stages or execute combined communication and charging performance testing in fully integrated laboratory environments.

Highlights:

• Instrumented MCS charging cable for EV-side validation
• Supports CE and ID signal measurement and logging
• Communication testing using Automotive Ethernet and Power Line Communication (PLC) technologies
• Compatible with SL1040A Portable CDS and SL1047A High-Power CDS
• Enables communication-only in combination with SL1550A EV – EVSE Charging Communication Interface Tester, standard-power, and high-power MCS test scenarios

Extend your Charging Discovery System for MCS testing

The SL2630A Add-on Box provides a fully instrumented MCS vehicle inlet for EVSE-side testing. It enables charging infrastructure manufacturers to validate communication behavior, interoperability, and charging performance of MCS-compliant chargers in a controlled and repeatable environment. The solution supports communication-only verification as well as combined communication and power testing up to 400 A and, when used with high-power CDS configurations, up to 800 A.

Highlights:

• MCS vehicle inlet interface for EVSE validation
• Supports CE and ID signaling according to IEC 61851-23-3
• Compatible with SL1040A Portable CDS and SL1047A High-Power CDS
• Enables communication-only in combination with SL1550A EV – EVSE Charging Communication Interface Tester, standard-power, and high-power MCS test scenarios

Keysight's BT2182A cable (4 m) are for 16 measurement channels to connects the DB37(f) on the Keysight BT2152B rear panel. The cable has 18 pairs of twisted wires with shield and braided shield around bundle of twisted pairs; only 16 pairs are necessary for current measurement with the BT2152B. The braid connects to the connector housing on both ends of cable; connector pins are machined.

Learn more about Keysight's self-discharge measurement solutions.
 

The Keysight BT2181A cable (2 m) for 16 measurement channels connects to the DB37(f) on Keysight's BT2152B rear panel. The cable has 18 pairs of twisted wires with shield and braided shield around bundle of twisted pairs; use the 16 pairs for current measurement with the BT2152B. Braid connects to the connector housing on both ends of the cable with machined connector pins.

Learn more about Keysight self-discharge measurement solutions.
 

For 16 measurement channels. One DB37(f) connector to connect to 16 channels of BT2152B. The DB37(f) connects on the board to two 16-pin screw terminal connectors (one for + terminal of all channels and one for – terminal of all channels). The screw terminal connectors support twisted-pair wiring (16-30 AWG) to the cells-under-test or to fixturing for the cells. Screw terminals are on 4 mm spacing. Boards have feet to use on a table and 4 mounting holes for standoffs and/or to attach the board inside test fixtures or cabinets. 

Learn more about Keysight Self-Discharge Measurement Solutions

Fixture has two DB37(m) connectors mounted on a PC board that connect to both BT2152B rear panel connectors. All 32 measurement channels are connected to a pair of banana terminals for a DMM used for verification test of BT2152B.

Learn more about Keysight Self-Discharge Measurement Solutions

Rack mount kit without handles for BT2152B Self-Discharge Analyzer.