Accessories

• Test and validate high-speed technologies such as DDR5 / MIPI with the 25 GHz probe amplifier (AP2).
• Experience the highest input impedance in midband frequencies for low-energy probing.
  
• Boost test margins with the lowest signal degradation.
• Probe small devices with the super-flexible micro probe head or choose from the widest variety of compatible probe heads for your unique application.
• Measure differential, single-ended, and common mode signals with a single probe tip.
  
• Use with Infiniium UXR-, 90000 X-, Q-, V-, and Z-Series oscilloscopes.

Keysight’s MX0025A InfiniiMax Ultra Series probe amplifier improves usability because you can measure differential, single-ended, and common mode signals with a single probe tip.

When you use a probe to connect your signal to your oscilloscope, it becomes part of the circuit affecting your test. Your probe may be hiding signal details, loading down your signal, or distorting it. InfiniiMax Ultra Series probes have the lowest loading for minimal impact to your circuit. Boost your test margins and gain measurement confidence with their unprecedented accuracy. Ensure your entire measurement system is helping you see the truest representation of your signal.

These probes have the lowest noise and capacitive loading and the lowest loading across more frequencies due to their RC high impedance profile. The InfiniiMax Ultra Series supports InfiniiMode and has a user-defined AC calibration mode, a wider input voltage range, more accuracy with unique S-parameter characterization, lower capacitive loading, a wider input voltage range, micro / socketed probe heads for smaller density probing, and more bandwidths. The InfiniiMax Ultra Series has an RC input impedance architecture with the lowest loading and least signal distortion across the widest frequency range.

InfiniiMax Ultra probes have three attenuation ranges — 1:1, 4:1, and 8:1 — giving you superior noise performance and large voltage ranges, all while maintaining maximum bandwidth. The input range automatically configures depending on the size of the input signal and vertical scale of your oscilloscope.

Choose from the three flexible input dynamic ranges from 600 mVpp at 1:1, 2.5 Vpp at 4:1, and 5 Vpp at 8:1. Clearly see and know when your design is satisfactory, keep up with standards, easily probe small devices, and reduce test complexity with the InfiniiMax Ultra Series probes.

Key Features:

• 2 GHz bandwidth (-3dB)
• High resistance (1MΩ) and low capacitance (1 pF) input for low loading
• Wide input dynamic range (±8V) and offset range (±12V)
• Built-in headlight for better visibility while probing
• Includes various probe tip accessories
• Direct connection to AutoProbe interface (no power supply required)

Compatible Oscilloscopes:

• Keysight InfiniiVision 3000/3000T X-, 4000 X-, 6000 X-, 5000, 6000 (except 6000 100 MHz), 7000 and Infiniium 9000, S-Series and 90000A Series.

The N2796A is a new generation of low-cost, single-ended active probe with the AutoProbe interface. The probe integrates many of the characteristics needed for today’s general-purpose, high-speed probing - especially in digital system design, component design/characterization, and educational research applications. Its 1MΩ input resistance and extremely low input capacitance (1 pF) provide ultra low loading of the DUT. This, accompanied with superior signal fidelity, makes this probe useful for most of today’s digital logic voltages. And with its wide dynamic range (±8 V) and offset range (±12 V), the probe can be used in a wide variety of applications.

For high signal integrity probing, the N2796A 2 GHz active probe is a perfect complement to Keysight’s 1 GHz bandwidth Infiniium and InfiniiVision Series scopes. The N2796A can also be used with Keysight’s 2.5 GHz or higher bandwidth Infiniium 9000 or 90000 Series scopes as a low-cost alternative to 1156A-1158A active probe or InfiniiMax probe.

The N2796A is equipped with a white LED headlight to illuminate the circuit under test. The probe is powered directly by the InfiniiVision and Infiniium AutoProbe interface, eliminating the need for an additional power supply. The probe also comes with a number of accessories that allow for easy connections to the circuit under test.

• Measure the average power of all modulation formats.
• Wide dynamic range power measurements from -30 dBm to +44 dBm.
• 10 MHz to 6 GHz frequency coverage for Wireless Comms formats.
• Low SWR for reducing mismatch uncertainty.
• Calibration factors, linearity and temperature compensation data stored in EEPROM.
• Compatible with EPM (N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters.

• Low frequency coverage (9 kHz to 6 GHz) for EMC/EMI test applications such as the radiated immunity test (IEC61000-4-3)
• High sensitivity (-60 to +20 dBm) and fast measurement speed to reduce the time taken to calibrate radiated field uniformity and EMC/EMI test receivers
• Measure transmitter power and receiver sensitivity at Very Low Frequency (VLF) to microwave frequencies
• Special option available to 18 GHz
• Compatible with EPM (N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters

The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty, which are reflections of the test signals. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.

• Frequency range: 10 MHz to 18 GHz    
  
• VSWR: < 1.3:1
• Connectors: BNC (f) input bias / 3.5 mm (m)
• Low SWR for reducing noise figure measurement uncertainty
• Individually calibrated ENR values at specific frequencies

The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source minimizes reflection of test signals, reducing measurement uncertainty. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).

• Frequency range: 10 MHz to 18 GHz
• VSWR: < 1.3:1
• Connectors: BNC (f) input bias / 3.5 mm (m)
• Low SWR for reducing noise figure measurement uncertainty
• Individually calibrated ENR values at specific frequencies

The AC68GPBU is a user-installable GPIB interface module upgrade for Keysight AC6800 Series basic AC power sources.

• Option available for the following models: AC6801B, AC6802B, AC6803B, AC6804B
• Order as: AC68GPBU
• Upgrade contents: GPIB module
• Adjustments required: No
• Additional requirements: No
• Installed by, estimated installation time: Customer, 3 minutes

Note: Only one slot available for either AC68GPBU GPIB Interface or AC68BALGU Analog Control or AC68BFIU Fault Interrupt

The Keysight DAQM910A module data acquisition system is a low-voltage 20-channel multiplexer module. It combines dense, multifunction switching with 80-channel-per-second scan rates to address a broad spectrum of low-voltage data acquisition applications. You can mix two- and four-wire channels on the same module. Additional features include the following:

• two- and four-wire scanning
• maximum 40 Vpk circuit protection and switching
• automatic voltage safety monitoring
• built-in thermocouple reference junction
• SCPI compatible with DAQM901A module (for voltage and temperature measurement applications)

The standard product includes the following:

• 1 DAQM910A multiplexer module
• 1 functional test certificate

Please Note: Firmware version A.03 or above is required on DAQ970A and DAQ973A for compatibility with the DAQM910A.

• Excellent SWR for reducing mismatch uncertainty
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST)
• Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter
• Accurate average power measurements over -70 to -20 dBm
• Frequency range 50 MHz to 26.5 GHz
• Diode power sensing element
• The Keysight 11708A 30 dB attenuator is supplied with 8480 series power sensors with the "D" suffix, for calibration with the power meter 0 dBm, 50 MHz reference.

Type

Superior RF Performance

• Isolation: > 100 dB to 4 GHz
• Insertion loss: < 0.2 dB to 2 GHz, < 0.25 dB to 4 GHz

Features

The Keysight 8762A offers excellent electrical and mechanical performance with broadband operation, high isolation, low SWR, long life, and exceptional repeatability.

Buy only the performance you need! Keysight offers a new line of latching coaxial switches that combine legendary reliability with the widest range of performance options available today. Learn more at: N1810TL Coaxial Switch

Learn more about Keysight Single-Pole Double-Throw Switches - SPDT
 

• Module plugs into rear-panel expansion slot
• Combines 10/100Mbit LAN port with VGA out
• LAN port is LXI compliant, enabling remote access, command, and printing
• Compatible with VNC viewer for secure access
• Web browser-based interface allows remote control -- ideal for accessing remote R&D and teaching labs.

LAN/VGA module gives you network connectivity and complete LXI compliant support as well as the ability to connect to an external monitor. Operate your scope remotely from your PC using the web browser interface with the virtual front panel interface that looks and acts as the real front panel on the scope with the same associated keys and knobs. Oscilloscope are required.

Soft carrying case for the Keysight InfiniiVision HD3 Series oscilloscope.