Data Sheets
85572A-006
• Enables portable EMF measurements from 30 MHz to 6 GHz with all Keysight FieldFox analyzers
• Supports spectrum analyzer EMF channel power measurements
• EMF measurements on 5G NR control channels show the impact of the 5G signal over total RF exposure, requires over-the-air (OTA) 5G NR (for FieldFox B-Series only)
Introduction
Radio frequency electromagnetic fields (EMF) testing is key to evaluate total RF exposure in any given area due to deployment of various RF/MW networks, such as mobile phones, base stations, Wi-Fi, smart meters, IoT devices, and satellite and radar systems. Exposure levels set by government and regulatory agencies need to be verified in the field for compliance.
FieldFox with EMF measurements (Option 358), connected to the 85562A-006 EMF Triaxial Isotropic Antenna, enables EMF measurements in spectrum analyzer and over-the-air (OTA) 5G NR modes. The total field strength can be measured across the frequency band of interest.
Key Specifications (FieldFox Analyzer + 85572A-006 Antenna)
Item |
Specifications |
System frequency range |
30 MHz ~ 6 GHz |
Measurement dynamic range |
0.2 mV/m to 200 V/m |
Max applicable field strength |
300 V/m |
Mode |
Sweep/FFT |
Trace |
X-Axis, Y-Axis, Z-Axis, current, isotropic, isotropic accumulated |
Limit lines |
MSL, ICNIRP |
Antenna type |
Triaxial isotropic antenna |
Antenna factor input methods |
Direct to the analyzer, auto download from antenna to SA |
Time averaging |
1 to 30 min (# of measurement= Measurement time/ (Dwell time x 3) |
Units[1] |
dBμV/m, dBm/𝑚𝑚2, V/m, W/c𝑚𝑚2, W/𝑚𝑚2, dBμA/m, dBG, dBpT |
Result type |
ACT, MIN, MAX, AVG, % of limit, spatial averaging |
Key Specifications for 85572A-006 Antenna
Keysight 85572A-006 EMF Triaxial Isotropic Antenna, originally designed and built in the AGOS NIRLab laboratory, contains three passive, independent, orthogonal antennas. If used with the supplied ferrite bead coaxial cable, it allows reliable measurement of radiofrequency electric fields that have an environmental impact in the vast majority of practical cases. The three orthogonal antennas are framed in the spherical radome.
Item |
Specifications |
Frequency range |
30 MHz ~ 6 GHz |
Transducer type |
Isotropic transducer with three orthogonal dipole antennas, with RF absorbing boom |
Polarization |
Linear, tri-axial polarization selection by means of internal electronic solid-state RF switch |
Axis selection |
By GPIO interface |
Linear dynamic range |
0.2 mV/m to 200 V/m (1 dB compression point) |
Sensitivity |
< 0.2 mV/m (depend of RBW and noise quality of spectrum analyzer |
Max applicable field strength |
300 V/m |
Probe linearity |
< 1.5 dB |
Isotropic error on rms total electric field |
±1.5 from 30 MHz to 1500 MHz ±2.0 from 1500 MHz to 2000 MHz ±2.5 from 2000 MHz to 3500 MHz ±3.5 from 3500 MHz to 6000 MHz |
Dimension |
Ø 77 mm, length 220 mm |
Antenna weight |
580 g |
RF connector |
N type Male, 50 ohm |
Protection class |
IP 42 |
Temperature range |
–20 °C to +55 °C |
Humidity |
Max 95% at 40 °C without condensation |
Shock resistance |
1 m drop without degradation of electrical characteristics
|
×
Please have a salesperson contact me.
*Indicates required field
Thank you
A sales representative will contact you soon.