Accessories

• Test and validate high-speed technologies such as DDR5 / MIPI with the 25 GHz probe amplifier (AP2).
• Experience the highest input impedance in midband frequencies for low-energy probing.
  
• Boost test margins with the lowest signal degradation.
• Probe small devices with the super-flexible micro probe head or choose from the widest variety of compatible probe heads for your unique application.
• Measure differential, single-ended, and common mode signals with a single probe tip.
  
• Use with Infiniium UXR-, 90000 X-, Q-, V-, and Z-Series oscilloscopes.

Keysight’s MX0025A InfiniiMax Ultra Series probe amplifier improves usability because you can measure differential, single-ended, and common mode signals with a single probe tip.

When you use a probe to connect your signal to your oscilloscope, it becomes part of the circuit affecting your test. Your probe may be hiding signal details, loading down your signal, or distorting it. InfiniiMax Ultra Series probes have the lowest loading for minimal impact to your circuit. Boost your test margins and gain measurement confidence with their unprecedented accuracy. Ensure your entire measurement system is helping you see the truest representation of your signal.

These probes have the lowest noise and capacitive loading and the lowest loading across more frequencies due to their RC high impedance profile. The InfiniiMax Ultra Series supports InfiniiMode and has a user-defined AC calibration mode, a wider input voltage range, more accuracy with unique S-parameter characterization, lower capacitive loading, a wider input voltage range, micro / socketed probe heads for smaller density probing, and more bandwidths. The InfiniiMax Ultra Series has an RC input impedance architecture with the lowest loading and least signal distortion across the widest frequency range.

InfiniiMax Ultra probes have three attenuation ranges — 1:1, 4:1, and 8:1 — giving you superior noise performance and large voltage ranges, all while maintaining maximum bandwidth. The input range automatically configures depending on the size of the input signal and vertical scale of your oscilloscope.

Choose from the three flexible input dynamic ranges from 600 mVpp at 1:1, 2.5 Vpp at 4:1, and 5 Vpp at 8:1. Clearly see and know when your design is satisfactory, keep up with standards, easily probe small devices, and reduce test complexity with the InfiniiMax Ultra Series probes.

The 42090A is an open termination and is primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using this standard.

The 42091A is a short termination and is primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using this standard.

The AE6941A Automotive Ethernet Electrical Test Fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.

You can use this breakout board with the AE6942A, AE6943A, and AE6960A adapters to support the Keysight AE6900T, AE6900R, and AE6900L automotive Ethernet electrical conformance applications to provide fast and accurate design validation and debug of transmit receive and link segment signals.

Features

• Complete 100BASE-T1 automotive Ethernet signal access for conformance testing and characterization
• Compliant with IEEE 802.3bw and IEEE 802.3b
• Flexible subMiniature A (SMA) connections for ease-of-use
• Versatile adapter boards available for various connector types including Mini-50, MATEnet and H-MTD

Supports standards 

• IEEE 802.3bw 100 Mb/s
• IEEE 802.3bp 1000 Mb/s
• IEEE 802.3ch multigigabit

• Nylon soft black carrying case with shoulder strap
• Also includes a storage pouch to keep your accessories secure

The N2738A Soft carrying case is the perfect way to travel with or store your 1000 X-Series oscilloscope. The case is designed for convenience with padded sides and bottom, as well as a storage pouch for your probes and additional accessories.
 

The N2733B Soft carrying case is the perfect way to travel with or store your InfiniiVision Series oscilloscope. The case is designed for convenience with padded sides and bottom, as well as a storage pouch for your probes and additional accessories.

• Low frequency coverage of 9 kHz to 6 GHz for EMC/EMI test applications such as the radiated immunity test (IEC61000-4-3)
• High sensitivity of -60 to +20 dBm and fast measurement speed to reduce the time taken to calibrate radiated field uniformity and EMC/EMI test receivers
• Measure transmitter power and receiver sensitivity at Very Low Frequency (VLF) to microwave frequencies
• Special option available for frequencies up to 18 GHz
• Compatible with EPM (N1913B/14B, N1913A/14A, E4418B/19B), EPM-P (E4416A/17A) and P-series (N1911A/12A) power meters

• Frequency range of 10 MHz to 6 GHz coverage for Wireless Comms formats
• Wide dynamic range power measurements from -30 to +44 dBm
• Measure the average power of all modulation formats
• Low SWR for reducing mismatch uncertainty
• Calibration factors, linearity, and temperature compensation data are stored in EEPROM
• Compatible with EPM (N1913B/14B, N1913A/14A, E4418B/19B), EPM-P (E4416A/17A) and P-series (N1911A/12A) power meters

The Keysight 346C noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 26.5 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. Option K01 is a coaxial noise source and features coverage from 1 to 50 GHz with a 2.4 mm coaxial connector.

• Frequency range: 10 MHz to 26.5 GHz
• VSWR: < 1.35:1
• Connectors: BNC (f) input bias / 3.5 mm (m)
• Low SWR for reducing noise figure measurement uncertainty
• Individually calibrated ENR values at specific frequencies

The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty, which are reflections of the test signals. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.

• Frequency range: 10 MHz to 18 GHz    
  
• VSWR: < 1.3:1
• Connectors: BNC (f) input bias / 3.5 mm (m)
• Low SWR for reducing noise figure measurement uncertainty
• Individually calibrated ENR values at specific frequencies

The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source minimizes reflection of test signals, reducing measurement uncertainty. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).

• Frequency range: 10 MHz to 18 GHz
• VSWR: < 1.3:1
• Connectors: BNC (f) input bias / 3.5 mm (m)
• Low SWR for reducing noise figure measurement uncertainty
• Individually calibrated ENR values at specific frequencies

The AC68GPBU is a user-installable GPIB interface module upgrade for Keysight AC6800 Series basic AC power sources.

• Option available for the following models: AC6801B, AC6802B, AC6803B, AC6804B
• Order as: AC68GPBU
• Upgrade contents: GPIB module
• Adjustments required: No
• Additional requirements: No
• Installed by, estimated installation time: Customer, 3 minutes

Note: Only one slot available for either AC68GPBU GPIB Interface or AC68BALGU Analog Control or AC68BFIU Fault Interrupt