Accessories

• Test and validate high-speed technologies such as DDR5 / MIPI with the 25 GHz probe amplifier (AP2).
• Experience the highest input impedance in midband frequencies for low-energy probing.
  
• Boost test margins with the lowest signal degradation.
• Probe small devices with the super-flexible micro probe head or choose from the widest variety of compatible probe heads for your unique application.
• Measure differential, single-ended, and common mode signals with a single probe tip.
  
• Use with Infiniium UXR-, 90000 X-, Q-, V-, and Z-Series oscilloscopes.

Keysight’s MX0025A InfiniiMax Ultra Series probe amplifier improves usability because you can measure differential, single-ended, and common mode signals with a single probe tip.

When you use a probe to connect your signal to your oscilloscope, it becomes part of the circuit affecting your test. Your probe may be hiding signal details, loading down your signal, or distorting it. InfiniiMax Ultra Series probes have the lowest loading for minimal impact to your circuit. Boost your test margins and gain measurement confidence with their unprecedented accuracy. Ensure your entire measurement system is helping you see the truest representation of your signal.

These probes have the lowest noise and capacitive loading and the lowest loading across more frequencies due to their RC high impedance profile. The InfiniiMax Ultra Series supports InfiniiMode and has a user-defined AC calibration mode, a wider input voltage range, more accuracy with unique S-parameter characterization, lower capacitive loading, a wider input voltage range, micro / socketed probe heads for smaller density probing, and more bandwidths. The InfiniiMax Ultra Series has an RC input impedance architecture with the lowest loading and least signal distortion across the widest frequency range.

InfiniiMax Ultra probes have three attenuation ranges — 1:1, 4:1, and 8:1 — giving you superior noise performance and large voltage ranges, all while maintaining maximum bandwidth. The input range automatically configures depending on the size of the input signal and vertical scale of your oscilloscope.

Choose from the three flexible input dynamic ranges from 600 mVpp at 1:1, 2.5 Vpp at 4:1, and 5 Vpp at 8:1. Clearly see and know when your design is satisfactory, keep up with standards, easily probe small devices, and reduce test complexity with the InfiniiMax Ultra Series probes.

• Adjust UXR-Series Oscilloscopes up to 110 GHz.
• Ruggedized 1.0 mm Female probe head.
• AutoProbe III interface.
• 3.5 mm Male RF Cable input.
• Probe Head Torque: 10 in-lb.

The Infiniium UXR-Series is the first real-time oscilloscope to offer an optional self-optimization module – capable of performing the frame adjustments to align internal correction constants under site environmental conditions. Optimization modules are available for all UXR-Series bulkhead connector types and supported bandwidths.

A full factory certified calibration consists of frame calibration adjustments, and subsequent testing and performance verification to ensure the oscilloscope is performing to its documented specifications. The optimization module performs only the factory-quality frame adjustment calibration steps. Additional instruments and components are necessary to perform the required horizontal adjustments and vertical performance verification procedures to achieve a full self-verified calibration. If an accredited certified calibration certificate is required, the UXR must be returned to a qualified Keysight service center.

• Adjusts UXR-Series Oscilloscopes with 40 to 70 GHz of bandwidth
• Ruggedized 1.85 mm Female probe head
• AutoProbe III interface
• 3.5 mm Male RF Cable input
• Probe Head Torque: 8 in-lb

The Infiniium UXR-Series is the first real-time oscilloscope to offer an optional self-optimization module – capable of performing the frame adjustments to align internal correction constants under site environmental conditions. Optimization modules are available for all UXR-Series bulkhead connector types and supported bandwidths.

A full factory certified calibration consists of frame calibration adjustments, and subsequent testing and performance verification to ensure the oscilloscope is performing to its documented specifications. The optimization module performs only the factory-quality frame adjustment calibration steps. Additional instruments and components are necessary to perform the required horizontal adjustments and vertical performance verification procedures to achieve a full self-verified calibration. If an accredited certified calibration certificate is required, the UXR must be returned to a qualified Keysight service center.

• Adjusts UXR-Series Oscilloscopes with 10 to 33 GHz of bandwidth
• Ruggedized 3.5 mm Female probe head
• AutoProbe II interface
• 3.5 mm Male RF Cable input
• Probe Head Torque: 8 in-lb

The Infiniium UXR-Series is the first real-time oscilloscope to offer an optional self-optimization module – capable of performing the frame adjustments to align internal correction constants under site environmental conditions. Optimization modules are available for all UXR-Series bulkhead connector types and supported bandwidths.

A full factory certified calibration consists of frame calibration adjustments, and subsequent testing and performance verification to ensure the oscilloscope is performing to its documented specifications. The optimization module performs only the factory-quality frame adjustment calibration steps. Additional instruments and components are necessary to perform the required horizontal adjustments and vertical performance verification procedures to achieve a full self-verified calibration. If an accredited certified calibration certificate is required, the UXR must be returned to a qualified Keysight service center.

• frequency range: DC to 100 kHz (-3dB with current de-rating)

• maximum peak current at 100 mV / A, 10 A DC or peak AC, 10 mV /A, 100 A DC, or peak AC

• AC current accuracy at 100 mV / A (50 mV to 10 A peak) - 3% of reading ≥ 50 mA, 10 mV / A (500 mA to 40 A peak), - 4% of reading ≥ 50 mA,10 mV / A (40 A to 100 A peak) - 15% maximum at 100 A

• working voltage at 600 V maximum

• battery: USB or 9 V alkaline

The Keysight 1146C AC / DC probe provides accurate display and measurement of currents up to 100 A DC or peak AC / DC to 100 kHz without breaking the circuit. The 1146C AC / DC probe has hall-effect sensor technology to measure AC and DC signals. It is compatible with any Keysight oscilloscope with 0.2 to 0.5 V / div sensitivity and 1 MΩ BNC input.

The 1146C AC / DC is ideal for capturing transient current signals in motor controllers, switching power supplies, inverters, and current amplifiers driving inductive loads.

The 1146C AC/DC probe replaces the discontinued 1146B with the same form, fit, and functionality while adding integrated USB power support for more flexible power options.

The SP0631A PXIe Switch PCIe cable adapter card is designed to create a flexible and scalable PXIe fabric solutio

Features

• PXIe System Module - Gen 4 x16 PCIe cable adapter
  
• 24 Lane PCIe backplane ports
• Up to 16 GT/s per PCIe lane
• 100 ns port latency
• Transparent PXIe expansion
• PCIe 4.0 and PXIE-1 rev 2.3 and PXISA PCIE-5 Hardware specification 1.1 compliance
• Quad SFF-8644 x4 cable ports
• Copper cable and fiber-optic cable support 0.5 to 100 meters

Capabilities and features:

• PCIe Gen4 x4 CMI copper cable

• Cable length of 1 meter
• Conforms to the mechanical dimensioning requirements of SFF-8644
• PCIe external cabling specification compliant
• x4 PCIe Gen 4 support
• 2 EEPROMs
• 100 Ohm cable PVC
• RoHS compliant

Features and capabilities:

• Wide operation range up to 3 kV/1500 A
• Fully automated fast thermal test from -50 °C to +250 °C
• Automatic power device (semiconductor and component) datasheet creation
• Auto record function to prevent data loss
• Fiber optic cable that enables connecting systems and I/O subsystems
• Conforms to the mechanical dimensioning requirements of SFF-8644 
• Compliant to SFF-8636
• x4 PCIe Gen 4 support
• 12 strand fiber
• Minimum bending radius of 30mm 
• 2 EEPROMs
• ROHS II compliant

The SP0632A PXIe Peripheral Module is designed to create a flexible and scalable CompactPCI Express/PXIe expansion solution. The SP0632A enables connectivity to other PXIe chassis utilizing the SP0631A PXIe switch card. 

Features

• PXIe Gen4 Transparent Peripheral Module
• 8 lane PCIe backplane ports
• Up to 16 GT/s per lane
• 100 ns port latency
• Transparent PXIe expansion
• Two SFF-8644 x4 cable ports
• Copper cable and fiber-optic cable support 0.5 to 100 meters
• 3U rack mountable

The SP0630A Gen4 Host/Target Adapter is a high-performance transparent solution for connecting servers to external I/O subsystems. For high performance applications, the SP0630A delivers flexibility and performance with extremely high data quality. 

Features

• PCIe Card - Gen4 x16 PCIe Transparent Host / Target Adapter
• PCI Express® 4.0 compliant - 16.0 GT/s per lane
• Link compliant with Gen1, Gen2, Gen3 and Gen4 PCI Express
• PCIe 4.0 cables
  
• Quad SFF-8644 x4 Gen4 PCI Express NTB cable ports that can be configured as:
  • One - x16 PCI Express port
  • Two - x8 PCI Express ports
  • Four - x4 PCI Express ports
• Supports both copper and fiber-optic cables
  
• Host clock isolation support
  
• Low profile PCI Express form factor
  
• Dual EEPROM / Flash for safe custom system configuration

10BASE-T1S Media Converter

The Keysight APM3000E enables you to convert the Ethernet physical layer from 10BASE-T1S Automotive Ethernet to 10/100/1000BASE-T.

• Low power consumption (10 W)
• Intuitive LED indicators:
  • Link status and network activity
• 25ns message time stamping precision
• Rugged aluminium enclosure with rubber bumbers for durability

The APM3000E media converter is required for Automotive Ethernet 10BASE-T1S receiver testing with Keysight AE6930R software.

Use with the following solution: AE6000R.

The 42090A is an open termination and is primarily used for performance tests of Keysight's 4-terminal pair LCR meters and impedance analyzers. Refer to the instrument's operation/service manual for the method of using this standard.