Low Frequency RFID Tag Characterization

The application note describes the features of N9321/22C basic spectrum analyzer and how it helps with RFID tag characterization.

Improving Test Efficiency of MEMS Electrostatic Actuators

This application brief describes how the Keysight E4980A LCR meter can greatly improve the test efficiency of MEMS electrostatic actuators. Learn more!

Battery Life Optimization for Wireless Medical Devices

Learn how to optimize battery life. Using a blip WiFi Blood Pressure Monitor as an actual use case, we explain how to measure battery life on a wireless medical device.

VTEP Clip for ICT – Installation Guide

See how the VTEP clip is installed to the VTEP amplifier board, sensor plate and hanger probes assembly for the Medalist in-circuit test (ICT) systems.

DOCSIS 3.1 PHY Layer Measurements

This paper describes RF tests for DOCSIS 3.1 CMTS and CM devices, and gives practical guidance for implementing them with Keysight DOCSIS 3.1 test equipment.

Overcoming Test Challenges of USB Type-C

An intro to the USB Type-C connector, the interface functions it provides, and test implications engineers face when integrating the connector into designs.

Monitoring and Controlling Particle Collisions at Nanometer Scale

The Large Hadron Collider (LHC) at CERN is a powerful particle accelerator. See how Keysight digitizers are used for control and diagnostics sections of the LHC.

Evaluating Adaptive Fast USB Battery Charging

Adaptive fast USB charging manages battery charging to assure safety and reliability. Learn how to simplify fast-charging battery operation!

Speed Time to Market from R&D Through Manufacturing

Learn the benefits of measurement consistency and having a choice of benchtop or modular instruments that are supported by common software applications.

Deploying Ideal Solution for Duplexer and Filter Tests

Learn why the E5080A Network Analyzer is the ideal solution for duplexer and handset filter test by enhancing yields with lower trace noise.

Automotive System Verification and Troubleshooting

Emerging technologies in the automotive industry are driving wide frequency applications. Find how to verify automotive system with FieldFox analyzers.

Dynamic BTS / UE Designs with 89600 Software

Gain deeper insights with the combined capabilities of an 89600 VSA and Wireless Link Analysis 89600 software, for dynamic BTS and UE designs.

Solutions for Emerging 4G and WLAN Communications Systems

This “Solutions for Emerging 4G and WLAN Communication Systems” application note explains how making Digital Pre-Distortion fast and practical for all engineers.

Pulse Signal Measurements the Easy Way

Using a Keysight N934xC and U2020 X-series peak power sensor in the field is a convenient way to test a pulsed signal, and obtain pulse parameters and peak power.

Rechargeable Battery Characterization

See how Keysight’s PA2200 Series Power Analyzers help you to simplify rechargeable batteries characterization for battery-powered products including battery life.

Designing for Modulation with Keysight EDA

Learn about the 8 great reasons why you use Keysight's EDA software to design with modulation.

Reducing Cost & Risk with Inspector Pre-Silicon Side Channel Analysis

Learn why detecting and analyzing side‑channel leakage early in the design cycle using Inspector Pre‑Silicon helps reduce cost and risk down the road. This webinar shows how simulation‑based SCA uncovers where and when leakage occurs, helps validate countermeasures, reduces costly redesigns, and strengthens chip‑level security before tape‑out.

Automated Wireless Coexistence Testing Using ANSI C63.27

This webinar outlines how automated wireless coexistence testing enables consistent, repeatable validation of medical devices against ANSI C63.27. It highlights structured workflows that support early risk identification, reduce manual effort, and guide Tier 1, Tier 2, and Tier 3 testing. The session includes a demonstration of the Keysight Wireless Coexistence Test Solution in a lab setting to support design confidence and regulatory readiness.

How to test a DC-DC converter using DAQ and BenchVue

Watch this video to learn how easy it is to test a DC-to-DC converter using PathWave BenchVue software and data acquisition system hardware. The PathWave BenchVue software helps you configure, intuitively control multiple instruments, and automate your test sequences quickly and with minimal instrument knowledge.

Introducing the PZ2100 High-Channel Density Precision SMU Solution (Without Sub-title)

Learn how the new PZ2100 SMU solution helps you overcome 5 key challenges testing low-power integrated circuits, and how it enables you to focus more of your time in testing, rather than implementation details.