Accessories

The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.

The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.

The Keysight E364SNP series and parallel kit is a simple, safe, and convenient solution for achieving series and parallel connections. With this kit, you can do the following:

• Combine all four channels into a single output, providing up to 128 V or 40 A with a total power of 400 W.
• Skip manual wired connections and instrument configuration steps.
• Switch easily between parallel and series modes for extended voltage or current ranges.

Use the Y1253A evaluation and prototyping board allows users to access individual single pins for prototyping or debugging. This is an M9195A/B PXIe DSR accessory.

• Board consists of 1 inch of signal header breakout pins, prototyping area with associated power connector, and signal termination pads.
• Offers 9 in² of bread board area, power/ground, includes headers for 16 channels, 16 PPMU channels high voltage and open drain channels.
• The Y1253A proto board is designed for use with the single-site, Y1246A and Y1247A cables only.

Key Benefits

• Allow user to deskew the time delay between voltage and current probes
• Easy to use and connect for current and voltage probes
• Directly connect to USB port from oscilloscope front panel, or any USB port from Personal Computer (PC) to power up the fixture

Requires:

• InfiniiVision 3000T, 4000X, 6000X, 5000, 6000 or 7000 or Infiniium S, 8000 or 9000 Series Oscilloscopes
• U1881A Power Measurement application for InfiniiVision 5000, 6000 and 7000 Series oscilloscopes; or U1882A Power Measurement application for Infiniium 8000 and 9000 Series oscilloscopes
• Current Probes
• Differential Active Probes

For accurate power measurements, it is extremely important to equalize the time delay between voltage and current probes. The U1880A deskew fixture allows you to drive both your voltage and current probes with the same pulse signal. Probe deskew can then be performed with the power measurements application software, or may be performed manually on the oscilloscope.

Power Measurement Software Download

Compatible Oscilloscopes:

• Infiniium 8000 Series
• Infiniium 9000 Series
• Infiniium 80000 Series
• Infiniium 90000 Series

E2649B USB 2.0 High-Speed Fixture Set test fixture for:

• Device High Speed Signal Quality testing
• Host High Speed Signal Quality testing
• Receiver Sensitivity testing
• Host Disconnect testing

Required for D9010USBC USB 2.0 compliance test software. Compatible with Infiniium 8000, 9000, 80000 and 90000 Series oscilloscopes.

• Provides test point access for transmitter measurements
• Single-ended measurements as required by the USB 3.0 specification for transmitter and receiver validation and pre-compliance testing
• Differential measurements using active probes allow probing of active bus transactions for debug and verification testing
• USB 3.0 power probing features for easy measurement of transient and steady state power states

The U7242A USB 3.0 test fixture will help simplify the USB 3.0 measurement process by providing access to the transmitter and receiver measurement points required for USB 3.0 compliance testing. It has been designed for direct SMA connections for easy and accurate measurements with direct connections to the oscilloscope and J-Bert SMA connections. It also includes probing connections for InfiniiMax active differential probes for the characterization and testing of active bus signaling of USB 3.0 and USB 2.0 traffic.

• Provides test point access for high performance transmitter signal integrity measurements
• Provides receiver test connections for receiver jitter tolerance testing
• Convenient plug on probing - Header access to the USB 3.0 and USB 2.0 signal lanes for
• Differential measurements using active probes allow probing of active bus transactions for debug and verification testing
• USB 3.0 power probing features for easy measurement of transient and steady state power states
• For fixture characterization and USB 3.0 test tool information, select the Related Products tab

• 20 GHz bandwidth (at -3 dB), de-embeddable up to 30 GHz
• Enables signal verification and debugging of USB4, USB4 Version 2.0, USB 3.x, DisplayPort 1.4/2.0/2.1, Thunderbolt 2/3/4, and MHL 3.3/SuperMHL
• Breaks out four lanes of high-speed signals for signal measurement or injection as well as low-speed power and control lines to a secondary fixture (N7016A Type-C low-speed fixture)
• Comes with the form factor to fit two fixtures side-by-side and/or top-and-bottom
• Provides the elements to seamlessly leverage Keysight’s portfolio of compliance test applications
• Compatible with Infiniium V-Series, 90000 X, Z-Series, and discontinued 90000 Q-Series

The N7015A type C test kit provides performance up to 30 GHz of de-embeddable bandwidth, enabling signal verification and debug of USB/DP/Thunderbolt designs and other high-speed signal standards to support type C connectors.

The N7015A high-speed USB type C fixture breaks out 4 lanes of high-speed signals for signal measurement or injection as well as low-speed power and control lines to a secondary fixture (N7016A) for monitoring and control. The flexible fixture kit enables signal accessibility and probing to the USB device, host (upstream and downstream) ports. The N7016A low-speed fixture manages power and control lines from the N7015A to support termination requirements, and test configuration as well as connection to a power delivery controller.

It comes with the form factor to fit two fixtures side-by-side and/or top-and-bottom. Whether connected side-by-side or stacked, the fixtures meet the minimum spacing allowed for in the specification. Durable fixture design ensures multiple connections and disconnections without failure in an active test environment.

See also N7015A/N7016A USB Type-C Interconnect Assembly Controller Software

Frequency:
1 kHz to 1 GHz

Sample Size (Toroids Only):
height: ≤ 8.5 mm
inner diameter: ≥ 3.1 mm
outer diameter: ≤ 20 mm

The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.

For more information about Material Testing Equipment, please visit Materials Test Equipment and LCR Meter & Impedance Measurement Product Accessories

Frequency:
≤ 30 MHz

Measurement parameters:
capacitance (C), dissipation factor (D), and dielectric constant (εr', εr'')

Material-under-test size:
thickness: ≤ 10 mm
diameter: 10 to 56 mm

The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.

For more information about Material Testing Equipment, please visit Materials Test Equipment.

Learn more about LCR Meter & Impedance Measurement Product Accessories

 

Frequency:
1 MHz to 1 GHz

Sample size (smooth sheets only):
thickness: 0.3 mm to 3 mm
diameter: ≥ 15 mm

The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixture, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixture has a flexible electrode that adjusts automatically to the material surface.

For more information about Material Testing Equipment, please visit Materials Test Equipment.

Learn more about LCR Meter & Impedance Measurement Product Accessories

• SMD, lead, and various types of devices are supported.
• Triaxial input terminal configuration minimizes the influences due to external noise, and as a result, high resistance up to 10 POhm can be measured accurately.
• A built-in interlock circuit enables safe high-voltage measurements.

The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.