Accessories

The Keysight U1180A thermocouple adapter and lead set are compatible with all series of Keysight Handheld Digital Multimeters. The set includes a J/K type Thermocouple adapter, thermocouple bead J-type and a thermocouple bead K-type.

• T/C Adapter J/K Type - Non compensation
• T/C Bead - J Type: Temperature rating (wire) -20°C - 200°C
• T/C Bead - K Type: Temperature rating (wire) -20°C - 200°C

The U1186A consists of a thermocouple bead (K-type) and a mini connector to dual banana plugs.

The operating range for the thermocouple is from -20°C to 200°C.

Accuracy: ±1.1°C.

• K-type bead probe supplied.
• Measures -50°C ~ 1000°C / -58°F ~ 1832°F.
• Slider switch to measure in °C or °F.
• 1 mV/°C or 1mV/°F output.
• Either Alkaline or Carbon-Zinc single standard 9V battery needed.
• To be used with Keysight handheld oscilloscopes or handheld digital multimeters.
  

The U1586B temperature adapter expands the capabilities of your handheld oscilloscope or handheld digital multimeter to measure temperature, either in °C of °F. To be used with a K-type bead thermocouple, and with approximately 1600 hours battery life with an alkaline battery, this adapter ensures you get the most out of your handheld scope or DMM purchase.

• Type J (iron – constantan) has a range (-40 °C to +750 °C) with higher sensitivity of about 50 µV/°C

The Keysight 34307A thermocouple kit contains 10 J-type thermocouples. Each thermocouple is 180 cm (72 inches) long.

The Keysight 34307A is compatible with the Keysight 34970A Data Acquisition/Switch Unit. The 34307A can also be used with the Keysight 34401A, 34460A or 34461A, however, an external program is required to convert the voltage measurements to temperature and an ice bath or electronic reference junction must be used.

The temperature probe measures dryer, transport pipe and surrounding air temperature within the range of -50°C to 800°C.

Measurement accuracy: 0.75% ± 2.2°C.

The temperature probe measures food, oil, and other liquids temperature within the range of -50°C to 700°C.

Measurement accuracy: 0.75% ± 2.2°C.

The temperature probe measures still surface temperature within the range of -50°C to 400°C. U1182A is used together with the U1586B temperature module. U1182A is compatible with the following handheld devices:

• Handheld Clamp Meter – U1212A, U1213A
• Handheld DMM – U1241A, U1241B, U1242A, U1242B, U1251A, U1252B, U1253A, U1253B, U1271A, U1272A
• Handheld Scope – U1602A, U1602B, U1604A, U1604B
• Handheld Calibrator – U1401A, U1401B
   

• Temperature range: -40 degrees C to 150 degrees C (-40 degrees F to 302 degrees F)
• Maximum temperature: 150 degrees C (302 degrees F)
• Accuracy: Typically less than 1 degrees C (2 degrees F). This varies with instrument and temperature range
• Time constant: 3 seconds (typical) from air to still water
• Dissipation constant: 5.7 mW/degrees C in still water
• Stainless steel probe dimensions: 1.5 inches long x 0.125 inches in diameter
• Length: 36 inch leads
• Termination: 3/4 inch dual banana plugs

The Keysight E2308A is a general purpose temperature probe. The thermistor (5 k ohm at 25 degrees C) is encapsulated in a stainless steel case and typically used for liquid temperature measurements.

The U1185A consists of a thermocouple bead (J-type) and a mini connector to dual banana plugs.

The operating range for the thermocouple is from -20°C to 200°C.

Accuracy: ±1.1°C.

Adapts thermocouple and temperature probes mini connector to dual banana inputs.