NOTE Features depend on installed hardware
and software options
Model |
Option |
Description |
E6607B E6607C |
|
Added new
feature in source to support WCDMA Band XIX (Band19). Added new feature to support LTE
Band 30 |
E6607A E6607B E6607C |
U9065A Sequence Analyzer |
Added new feature to support WCDMA
Band XIX (Band19). Added new
feature to support LTE Band 30 |
Model |
Option |
Description |
E6607A E6607B E6607C |
|
Fixed
a defect: Bluetooth waveforms
sometimes cannot be played, if updates to Signal Studio decryption components
are preventing markers in the waveform from being identified correctly. Fixed
defect – When running a source list with repetition type set to continuous,
at the start of a new sequence iteration there can
be a delay in the timing of amplitude and frequency changes with a loss of
synchronization with the ARB waveforms. Fixed
defect – When a source list sequence is stopped before completion, the source
output is not stopped cleanly. Fixed
defect – A source unleveled or source synthesizer unlocked status occurs when
a source list sequence is stopped before completion. |
E6607A E6607B E6607C |
U9065A Sequence
Analyzer |
Fixed
a defect: Sequence sometimes incorrectly reported the error message “Auto Set
RF Level failed”, even though the dynamic range was not exceeded, owing to an
error in floating point calculation precision. Fixed
defect – The step number is sometimes shown incorrectly in the error message
“Setting conflict; Analysis Offset should be greater than # us, Acq = # Step = #).
Fixed
defect – Results are sometimes not calculated for one measurement among
others in a sequence. |
Back to top of page
Model |
Option |
Description |
E6607A E6607B E6607C |
|
Adds support
for continuous playing of Source List Sequence. |
Model |
Option |
Description |
E6607A E6607B E6607C |
|
Fixed a
defect - Duration Time does not work from the RUI when duration type is set
to Continuous Abort. Fixed a
defect – Delay of output amplitude transition in a Source List Sequencer, on
a step with Waveform set to Continue Previous. Fixed a
defect – In a Source List Sequence using the Continue Previous waveform
setting, the RF amplitude and frequency transitions of the arbitrary waveform
generator can drift out of alignment over a large number of steps. |
E6607C |
|
Fixed a
defect – In the Sequence Analyzer mode, the Basic Tx
Power result is incorrect when the Peak Power is set above 34 dBm. |
E6607A E6607B E6607C |
U9065A Sequence
Analyzer |
Fixed a
defect – Occasional bad Phase Error results from LTE EVM measurements in some corner cases |
Back to top of page
Model |
Option |
Description |
E6607A E6607B E6607C |
U9065A Sequence Analyzer |
Add Support for LTE-FDD BAND 27, 28,
31and LTE-TDD Band 44. |
Model |
Option |
Description |
E6607A |
|
Fixed a
defect – Source Synthesizer PLLs requires additional settling time at power
up to stabilize FPGA DCM initialization. |
E6607A E6607B E6607C |
Fixed a defect – Source list can’t
play precisely as defined step length when use different ARBs in different
steps |
|
E6607C |
|
Fixed a defect – The output signal
could be turned off when the receiver and source step triggers arrived at the
MPA within 6 us. |
|
U9065A Sequence
Analyzer |
Fixed
a defect – Correction Table is not applied to WCDMA Phase Discontinuity power
results Fixed
a defect – EXT Basic PAvT power reading is lower
when trigger delay is set to 0 Fixed
a defect – LTE-FDD and LTE-TDD Mod Acc can’t handle
actual DUT signal when signal quality is bad Fixed a
defect – CDMA2000 Mod Acc cause crash when the EVM
test fails Fixed
a defect – Sequence Analyzer acquisition timing is incorrect in few corner
cases. |
Back to top of page
Model |
Option |
Description |
E6607C |
E6607C-PB2 |
Improved
maximum allowable external fixture loss requirement from 50dB to 100dB |
Model |
Option |
Description |
|
U9065A Sequence
Analyzer |
Fixed
a defect – Source List Sequencer “Continue as Previous” caused ARB to not
play out correctly when using SOURce:LIST:SET:WAVeform Fixed
a defect – Correct a potential timeout in Asynchronous fetch when the queried
acquisition is the last acquisition |
Back to top of
page
Model |
Option |
Description |
E6607C |
E6607C-PB2 |
Improved
minimum external fixture loss requirement from 6dB to 0dB. Upgrading to this
version requires re-calibration for option PB2. |
Model |
Option |
Description |
E6607A E6607B E6607C |
Fixed a
defect – when select GPS port, UI power range is not set correctly when
output level is set to below -130dB Fixed a
defect – multi-pack license may lose with low possibility if box is shut down
incorrectly by removing the power supply instead pressing the power button |
|
|
U9065A Sequence
Analyzer |
Fixed
a defect – Basic IQ returns infinite amplitude results when input level is
very low Fixed
a defect – sequence analyzer UI may stop response if user uses softkey and
SCPI command to setup sequence alternatively and quickly. Fixed
a defect – Leased Mode SCPI in EXT Sequence Analyzer is not available when
sequence analyzer is not preloaded Fixed
a defect – GGE T0 Offset result is not compensated by the Trigger Delay and
Analysis Offset which is different from one button mode. |
|
U9077A WLAN |
Fixed a defect – WLAN 11n 20MHz/40MHz ModAcc
got null reference exception |
Back to top of
page
Model |
Option |
Description |
E6607A E6607B E6607C |
Adds
support for the E6607C EXT with embedded Multi-Port-Adapter. Source
output level range is extended and supported to -150 dBm. |
|
|
U9065A Sequence
Analyzer |
Basic IQ
measurements in Sequence Analyzer can return power results when average
number >1. Minimum gap
between Power Accumulation Measurements reduced from 333µS to 0µS. Maximum acquisitions
per sequence increases from 512 steps to 1000 steps. Maximum
number of frequency changes per sequence increases from 203 to 400 hops. |
U9079A TD-SCDMA |
TD-SCDMA is
now supported in the Sequence Analyzer Adds
demodulation of TD-SCDMA continuous mode in Sequence Analyzer. |
|
U9082A LTE-TDD |
LTE-TDD is
now supported in the Sequence Analyzer |
Model |
Option |
Description |
E6607A E6607B |
Fixed
a defect – “LSEQ:WCDMA:RADio:DEVice
MS” now works. Fixed
a defect – There is no output signal when set source list sequence “Step Waveform”
to ‘Off’ through menu setting. Fixed
a defect – Source self-test doesn’t display test result other than ALC test, it
now reports all results Fixed a defect – powering off an external MPA
while it is connected to E6607A/B can cause the message “Hardware
configuration update” to pop-up and leave the instrument un-useable until it
is power cycled. The issue has now been fixed and MPA can be powered down
while connected. |
|
|
U9065A Sequence
Analyzer |
Fixed
a defect – ORFS under SEQAN may glitch randomly when testing a DUT. Fixed a defect – Minimum transition time from one
step to the next is a sequence was not calculated correctly. Fixed a defect – Multiple power accumulations
with samples < 5 and small gaps could cause a power accumulation to be
skipped. |
|
U9079A TD-SCDMA |
Fixed a
defect – TD-SCDMA Mod Acc measurement has unexpected
frequency error. Fixed
a defect – TD-SCDMA PvT random failure when RRC
filtering is performed. |
|
U9080A LTE-FDD |
Fix a defect - LTE
time offset result was not compensated correctly in Sequence Analyzer. |
|
U9082A LTE-TDD |
Fix a defect - LTE
time offset result was not compensated correctly in Sequence Analyzer. Fixed a
defect – LTE TDD PvT reported burst not found when
in external trigger. Implemented an improved algorithm to detect low power
burst measurement. |
Back to top of
page
Model |
Option |
Description |
E6607A E6607B |
Add support
for option 504 for the E6607B only (Option 504 – maximum input and
output frequency of 3.8 GHz) Restore or
Back-up of instrument calibration data (System->Alignments->Backup or
Restore Align Data) will now inform the user that the application will be
closed, and require a response, before the operation continues. This ensures
that after a restore calibration data operation the system reboots and
restored data is applied. Extend the
lowest settable range of source output to -130 dBm. Increased
Arbitrary Waveform segment names from 33 characters maximum to 128 characters
in the ARB sequence file. Improved
sequence set-up till ready for first measurement time in some cases by
increasing correction caching. |
|
|
U9065A |
In sequence
analyzer mode, the frequency offset for EDGE ORFS measurement is extended to
+/- 2.0 MHz. |
|
U9071A |
GSM/EDGE
Supports loop-back Bit Error Rate testing |
|
U9073A |
WCDMA
Supports loop-back Bit Error Rate testing |
U9079A |
TD-SCDMA
Support radio band frequency setting for internal source |
|
U9082A |
LTE-TDD
Support radio band frequency setting for internal source |
Model |
Option |
Description |
E6607A E6607B |
Fixed a
defect – In Sequence Analyzer an analyzer sequence that has only Basic TX
power did not work correctly. Fixed a
defect - *RST or Mode Preset did not preset channel number in some cases. Fixed a
defect – IS95 time offset had an incorrect result. Fixed a
defect – E6617A MPA On/Off setting and RFIO1 not correct when recalling state
files. Fixed a
defect – Internal source would go unleveled when Frequency Offset is
unspecified in the waveform header. Fixed a
defect - Exception thrown when SCPI parameter 0 was given in “SYST:LKEY:WAV:LOCK 0” command. Fixed a
defect - E6617A MPA Surprise removal (unplugging) USB cable could cause E6607
to crash with “Blue Screen” Fixed a
defect - E6617A MPA power cycle while connected to E6607 intermittently would
not power-on reliably. Fixed a
defect – Source module could intermittently get out of synch with calibration
data causing 1-2 dBm amplitude error of source signals. . |
|
|
|
|
|
|
|
Back to top of
page
Model |
Option |
Description |
E6607A E6607B |
Adds support for new more highly automated instrument
Software upgrade process (install wizard now removes old software version and
installs new software version without manual steps – only requires you to be
logged in as administrator). Multiple
enhancements to speed measurement time in all modes |
|
E6617A |
|
Adds support for E6617A
Multi Port Adaptor module |
U9079A |
Added
TD-SCDMA (U9079A) mode |
|
U9082A |
Added
LTE-TDD (U9082A) mode |
|
|
U9065A |
Added new SCPI SOURce:LIST:INITiation:ARMed?
Added new
SCPI INIT:LSEQ:ARMed? And INIT:LSEQuencer:ARMed Added new SCPI :SOURce:LIST:TRIGger:INITiation:ARMed?”
Added new
SCPI blocks to set-up ListSequencer analysis step
parameters individually. (See [:SENSe:]LSEQuencer block). ListSequencer – Source trigger can now be enabled
or disabled for each acquisition step |
U9080A LTE-FDD |
LTE-FDD is
now supported in the Sequence Analyzer Added in
LTE the ability for demodulation to now detect cyclic shift automatically. |
Model |
Option |
Description |
E6607A E6607B |
Fixed a
defect – auto alignment is no longer being started on Restart sweep. Fixed a
defect - Turn on EXT preamp in Auto Set RF Level may make noise floor worse in some
corner cases. Fixed a defect
- Source Preset change other settings than source control. |
|
|
U9065A |
Fixed a
defect - querying Radio device we always returned value+1. Fixed a
defect - the EVM 95% confidence peak will now accumulate across multiple
analysis steps. Fixed a defect
– Source list sequencer SCPI no longer rejects the “Time” or “Count” setting
when type is “CONTinuous”. Fixed a
defect - Downlink causes crash when IQ data is < 1 frame. Fixed a
defect - LSEQ GSM PFER T0 Offset result value too large. |
U9080A |
Fixed a
defect - Basic Tx Power measurement uses wrong IFBW
when radio standard is LTE |
Back to top of
page
Model |
Option |
Description |
E6607A E6607B |
Adds
support for E6607A replacement parts: A13 [E6607-61004] and A15 [N9020-63098] Adds
support for E6607B-503 Adds support for E6607-60012 Source module Adds support for the Quad core CPU processor N2S+ (PC4) Added
Source IQ alignment for customer use to improve EVM results. Added
Source Self Check system diagnostic |
|
U9075A U9081A |
Added WiMAX
U9075A and Bluetooth U9081A modes |
Model |
Option |
Description |
E6607A E6607B |
Fixed a
defect - if AutoAlign is off we now do-not initiate
a partial alignment during IF path change. |
|
U9065A |
Fixed a defect – ListSequences
of more than 256 acquisitions would return corrupt results. Fixed a defect – SourceSequence
– a source step at the end of a sequence transmits the wrong power level. |
|
U9072A |
Fixed a defect - with incorrect data
length is set when making a cdma2000 measurement |
|
U9080A |
Fixed multiple defects with LTE-FDD
help text |
Back to top of
page
Model |
Option |
Description |
E6607A |
Added an
FPGA update warning message in multiple languages to improve user experience
during the EXT software upgrade process |
Model |
Option |
Description |
E6607A |
Fixed a
software crash in GSM demodulation measurements of GMSK frequency and phase
error. |
|
U9065A U9071A U9080A |
Fixed a defect in the Source IQ Cal
function which produced degraded source EVM performance at 3 GHz. |
|
Fixed a defect which caused both
source modulation and source CW output to be turned off when modulation was
disabled. |
||
Fixed a defect which incorrectly
reported "Error 241 HW missing; option not installed" |
||
Fixed a defect which reported
instrument alignment failures by allowing in-progress alignments and expired
alignments to complete before start measurements in list sequencer mode. |
Back to top of
page
Model |
Option |
Description |
E6607A |
Added waveform data markers. |
|
U9065A |
Added Phase
Discontinuity measurement for WCDMA. |
|
Updated GSM
PvT to include Margin, Averaged Time Offset Power,
and Time Offset Power Reference results.
Improved filtering. |
||
Improved GSM
measurement throughput. |
||
Added
ability to query results from one step of a sequence when subsequent steps
are in process. |
||
Added
ability for ARB waveform to continue playing when a sequence is finished. |
Model |
Option |
Description |
E6607A |
Fixed marker symbols in I/Q Analyzer. |
|
U9065A |
Fixed
situation where trigger delay from one red-bar is propagated to the next
red-bar when trigger type is Free Run. |
|
Fixed
problem where high GSM EVM Phase Error results were reported. |
Back to top of
page
Model |
Option |
Description |
E6607A |
Added support for U9075A WiMAX 801.16 OFDMA
Measurement Application. |
|
Added Align Source to perform an I/Q alignment of the source for situations where the
source EVM performance changes due to temperature variation. |
||
U9065A |
Added
Amplitude Corrections to Basic IQ measurement. |
Model |
Option |
Description |
E6607A |
Fixed
problem where Waveform Slot associations were erased upon software update. |
|
Fixed
problem where the start-up message regarding Anti-Virus software continues to
be displayed even after the ‘do not show this message’ box is checked. |
Back to top of
page
Initial revision.
Back to top of
page
©
Copyright 2010, 2011 Agilent Technologies, Inc. All rights reserved.
Other product and company names herein may be the trademarks of their
respective owners.