Choose a country or area to see content specific to your location

PRODUCTS AND SERVICES
 Oscilloscopes

Analyzers
 Spectrum Analyzers (Signal Analyzers)
 Network Analyzers
 Logic Analyzers
 Protocol Analyzers and Exercisers
 Bit Error Ratio Testers
 Noise Figure Analyzers and Noise Sources
 HighSpeed Digitizers and Multichannel DAQ Solutions
 AC Power Analyzers
 DC Power Analyzers
 Materials Test Equipment
 Device Current Waveform Analyzers
 Parameter / Device Analyzers and Curve Tracers
 Meters
 Generators, Sources, and Power Supplies
 Software
 Wireless
 Modular Instruments
 Network Test and Security
 Network Visibility
 Services
 Additional Products
 All Products, Software, Services

Solutions

Explore by Use Case
Explore by Industry
 All Solutions
 Insights
 Resources
 Buy
 Support
What are you looking for?
Impedance Measurement Handbook
Introduction
In this document, not only currently available products but also discontinued and/or obsolete products will be shown as reference solutions to leverage Keysight’s impedance measurement expertise for specific application requirements. For whatever application or industry you work in, Keysight offers excellent performance and high reliability to give you confidence when making impedance measurements. The table below shows the product status of instruments, accessories, and fixtures listed in this document. Please note that the status is subject to change without notice.
1.0 Impedance Measurement Basics
1.1 Impedance
Impedance is an important parameter used to characterize electronic circuits, components, and the materials used to make components. Impedance (Z) is generally defined as the total opposition a device or circuit offers to the flow of an alternating current (AC) at a given frequency and is represented as a complex quantity that is graphically shown on a vector plane. An impedance vector consists of a real part (resistance, R) and an imaginary part (reactance, X) as shown in Figure 11. Impedance can be expressed using the rectangularcoordinate form R + jX or in the polar form as a magnitude and phase angle: Z_ θ. Figure 11 also shows the mathematical relationship between R, X, Z, and θ . In some cases, using the reciprocal of impedance is mathematically expedient. In which case 1/Z = 1/(R + jX) = Y = G + jB, where Y represents admittance, G conductance, and B susceptance. The unit of impedance is the ohm (Ω), and admittance is the siemen (S). Impedance is a commonly used parameter and is especially useful for representing a series connection of resistance and reactance, because it can be expressed simply as a sum, R and X. For a parallel connection, it is better to use admittance (see Figure 12.).
Reactance takes two forms: inductive (XL) and capacitive (Xc). By definition, XL =2πfL and Xc = 1/(2πfC), where f is the frequency of interest, L is inductance, and C is capacitance. 2πf can be substituted for by the angular frequency (ω: omega) to represent XL = ωL and Xc =1/(ωC). Refer to Figure 13.
A similar reciprocal relationship applies to susceptance and admittance. Figure 14 shows a typical representation for a resistance and a reactance connected in series or in parallel.
The quality factor (Q) serves as a measure of a reactance’s purity (how close it is to be a pure reactance, no resistance), and is defined as the ratio of the energy stored in a component to the energy dissipated by the component. Q is a dimensionless unit and is expressed as Q = X/R = B/G. From Figure 14, you can see that Q is the tangent of the angle θ. Q is commonly applied to inductors; for capacitors the term more often used to express purity is dissipation factor (D). This quantity is simply the reciprocal of Q, it is the tangent of the complementary angle of θ, the angle δ shown in Figure 14 (d).
1.2 Measuring impedance
To find the impedance, we need to measure at least two values because impedance is a complex quantity. Many modern impedance measuring instruments measure the real and the imaginary parts of an impedance vector and then convert them into the desired parameters such as Z, θ, Y, R, X, G, B, C, and L. It is only necessary to connect the unknown component, circuit, or material to the instrument. Measurement ranges and accuracy for a variety of impedance parameters are determined from those specified for impedance measurement. Automated measurement instruments allow you to make a measurement by merely connecting the unknown component, circuit, or material to the instrument. However, sometimes the instrument will display an unexpected result (too high or too low.) One possible cause of this problem is incorrect measurement technique, or the natural behavior of the unknown device. In this section, we will focus on the traditional passive components and discuss their natural behavior in the real world as compared to their ideal behavior.
 © Keysight Technologies 2000–2023
 Privacy
 Sitemap
 Terms
 Trademark Acknowledgements
 Feedback