How to Accurately Measure Resistance Using a Digital Multimeter

Learn how to use the Kelvin measurement method or the 4-wire measurement setup using a digital multimeter to make accurate resistance measurements.

How to Control and Automate in Python Using the Digital Learning Suite

This video will show you steps to setup your software and hardware to control your instruments in Python using the Digital Learning Suite as the front user interface.

AI-Assisted Design of Microwave Circuits

In this video, learn about how AI and Machine learning provide a design assistant for RF Circuit design. Python APIs unlock the ADS architecture, allowing unparalleled control over internal functions. Swedish graduate students create filters in the form of QR codes and run repeated simulations in RFPro to identify the versions that meet the optimal design specifications.

DC-DC Converter Load Regulation Test Demonstration

This video demonstrates how you can easily test the load regulation of a DC-DC converter. Load regulation test measures the ability of the DC-DC converter to sustain the specified voltage output when the load current varies at constant input voltage.

DLS diode characterization

How-To Video to demonstrate characterizing an active electronic components using Digital Learning Suite and basic bench instruments.

How to Test Charge Conformance for EVs

In this demonstration, we will show how you can meet these challenges and streamline your EV interoperability and conformance testing with automated software and a modular, upgradable test system.

DC-DC Converter Testing Demo

Learn how to quickly test load regulation, line regulation, turn-on time quickly, turn-off time, output ripple, and efficiency of a DC-DC converter. The video demonstration how you use these tests to select the correct converter for your application.

How To Design Phased Array Systems

This video presents the most important considerations for phased array system design, especially popular for proposed 5G architectures.

CODE V Jumpstart

Learn the fundamental concepts of using CODE V, from making and analyzing a lens to improving it with the CODE V optimizer, Automatic Design.

100G electrical conformance test solution

Keysight’s new pre-conformance 100GAUI-1 compliance test solution simplifies the testing of 100Gbps electrical interfaces by automating over 120 transmitter measurements (Tx) and receiver test procedures (Rx) for chip-to-module (C2M) and chip-to-chip (C2C) interfaces. The move to 100Gb/s and 53Gbaud PAM4 enables new technology such as 800G optical transceivers, as well as 51.2 terabit switches. This optimizes bandwidth and switching capacity, whilst reducing the cost and power consumption for the user. Our 112G compliance test solution offers features such as the automated optimization of reference equalizer (CTLE+DFE) and transmitter de-emphasis settings. The solution also provides accurate and repeatable test results following the latest developments of the IEEE 802.3ck recommendations, this includes the latest IEEE 400G ethernet standard. This reduces the characterization time for R&D teams of data center chips, switches, and systems vendors, from hours to minutes. With the guided setup, turn-key automated stress signal calibration, and conformance measurement, this test application provides robust and repeatable test results and minimizes the need for user interaction. For more information on our optical portfolio and Keysight’s 800G solutions please visit: https://www.keysight.com/find/800G

Quick-Start Video for 3D Interconnect Designer

In this quick-start tutorial, you will build a complete die-to-die interconnect without using the wizard. The video walks through the core design workflow, including how to create a new project, define substrates, create component definitions, place bump maps, connect nets, add dies, create interconnect buses, and prepare for link-level simulation.

Measuring Inrush Current with an IntegraVision Power Analyzer

Quickly, visualize and measure inrush current with an IntegraVision Power Analyzer. Inrush currents are typically very large compared to the steady state current, but they don’t last long. The wide dynamic range of the IntegraVision power analyzer is ideal for visualizing and measuring transient events, such as the inrush current.

DDR Simulation with Memory Designer and SIPro

Simulating your DDR4 or DDR5 memory design is much easier with Keysight's new workflow. This video will demonstrate an EM extraction of a PCB with SIPro, perform a Signal Integrity system-level analysis, and then a DDR compliance test in PathWave ADS Memory Designer.

How to Test Wireless Coexistence for Medical Devices Video

This is a how-to video which showcases the importance of testing medical devices with wireless interfaces and by using the Keysight Wireless Coexistence Test solution, engineers can accurately and repeatably test their devices to shorten development cycles, and gain earlier insight into how their devices perform in real-world RF environments.

Quantum EDA Solutions

In this video, we explore how to navigate the design challenges of superconducting quantum chips using Keysight Quantum EDA solutions. We cover the integrated workflow for quantum chips and highlight our three unique solutions: Quantum Layout, QuantumPro, and Quantum Circuit Simulation.

Quantum Layout

The Keysight Quantum Layout solution simplifies quantum chip design with an extensive library of resonators and qubits. Our quantum technology jump-starts your development process, while automated airbridges eliminate the hassle of dealing with unwanted CPW line modes. Plus, our multilayer technology makes it easy to scale up the number of qubits.

How to Use the Optical Mode Solver from Keysight Photonic Designer

This video demonstrates how to use the new optical mode solver GUI in Keysight Photonic Designer (W3803B) for calculating waveguide modes and directional couplers. It also showcases the Python API, enabling automated simulations, parameter sweeps, and advanced photonic design workflows.

N6700C Unboxing and Module Installation

In this video, we unbox the N6700C DC power supply and show you all the documentation and components that come with a mainframe. Plus, we will take you through the step-by-step process for installing a module.

How to Test MRI RF Coils

Optimizing RF coil performance requires proper design simulation and multi-channel testing to ensure high-quality MRI images and patient safety. Learn how to use modeling, simulations, and characterization tools from Keysight to test the RF coil for MRI machine.

Best Practices for Rack Mounting an N6700C

This video will teach you best practices for installing the N6700 DC power supply in a rack mount. These practices will ensure the unit's safety, reliability, and performance when part of a rack mount system.