PathWave Design Software Insights

Broadcast Date: October 24, 2019

Circuit designers are on the leading edge of new technology standards, including 5G. This webinar describes design techniques, simulation, and analysis of a 5G 28-GHz phased-array transmit chain with 4x4 beam-steered patch antenna array.

Broadcast Date: January 29, 2020

High-frequency circuit designers often struggle with stability. Learn techniques to identify and solve stability problems in the design phase before they become headaches in the lab.

Broadcast Date: February 26, 2020

Looking to push your DDR5 memory technology out to market faster? Learn what you need to know before simulating DDR5 buses in this webinar.

Broadcast Date: April 14, 2020

Todd Bermensolo will present IBIS-AMI Fundamentals that introduces the basic concepts for new IBIS-AMI modelers using Keysight’s PathWave System Design. It includes an overview of an IBIS-AMI simulation, key building blocks and preliminary introduction to model development flow.

Broadcast Date: April 23, 2020

EMI noise in high-speed switched-mode power converters can be examined by building a virtual prototype, then analyzing results using post-layout electromagnetic simulation techniques. Conducted and radiated EMI issues can be overcome using PathWave ADS Power Electronics, a common user environment of circuit simulation, layout, and field solvers.

Broadcast Date: April 29, 2020

In this webinar, you will learn how to build up a component library consisting of fast and accurate simulation models of the power devices that you use in switched-mode power supply circuit simulation.

Broadcast Date: May 6, 2020

Measuring voltage at an FPGA load is not too difficult, but a current measurement at the load is not possible. PathWave ADS simulation can help. Learn how a measurement of dynamic voltage can synthesize the dynamic current at the FPGA.  

Broadcast Date: May 6, 2020
Duration: 3 hours

Join us for a virtual seminar with our Keysight PCIe 5.0, DDR5, Simulation experts, and others in your field. 

Broadcast Date: May 7, 2020

This webinar introduces a robust design workflow that facilitates efficient Signal Integrity analysis and troubleshooting.

Broadcast Date: May 12, 2020
Duration: 4 hours

Automotive serial buses must be able to operate reliably in the harsh electrical environment of a vehicle where random and infrequent transients occur. New memory technologies (such as LPDDR4), faster processing, and higher sensor resolution are driving significantly faster serial bus speeds, which in turn reduces margins. Successful programs must closely attend to signal integrity for an on-time product launch. This seminar will provide valuable insight into design and measurement methods for meeting program schedules and costs.

Broadcast Date: May 19, 2020

RFPro makes spontaneous EM-circuit co-simulation effortless for designers of RFIC, Modules, Wafer-level packagings, and RF PCBs to achieve design wins in 5G, radars, and IoT.

Broadcast Date: June 2, 2020
Duration: 1 hour

If you are a circuit designer looking to simulate modulated signals such as ACPR and EVM or a system designer looking to add more accuracy and fidelity to your work, this virtual seminar will answer many of your questions on how best to tackle nonlinear RF system simulation for 5G and Aerospace applications.

Broadcast Date: June 16, 2020

Text for Card: Join us for a virtual seminar introducing PathWave Advanced Design System (ADS). Our expert will cover linear design techniques including S-parameter simulation, impedance matching, tuning, and optimization. The presentation also touches on non-linear frequency- and time-domain simulation, EM Simulation, and passive and active RF device models.

Broadcast Date: June 24, 2020

The use of millimeter-wave (mmWave) frequency for 5G and 6G communication systems is a common topic in the research community, but mmWave does have its challenges. Beamforming techniques are beneficial, but controlling and optimizing beams is difficult. Analyzing them is even more so. This webinar will demonstrate a model-based phased array system design and simulation to characterize a beam pattern. It will analyze spectral coverage using an unprecedented three-dimensional composite radiation pattern display technique. 

​​​​​Design your day around our virtual mmWave innovations design course featuring new PathWave Design software applications.

Overview:

• Presentation #1: EM/Circuit Co-Simulation (30 Minutes)
• Presentation #2: Complex Circuit Analysis (30 Minutes)
  
• Presentation #3: Phased-Array Design (30 Minutes)
  

In this series of virtual seminars, you will learn about the latest power amplifier design methodologies.

Broadcast Date: July 30, 2020
Duration: 1 hour

Learn how to set up and run thermal simulations in ADS. This talk will cover both electro-thermal co-simulations as well as layout-only thermal simulations. 

Broadcast Date: August 4, 2020
Duration: 90 min.

Co-sponsor: Newark and Picotest 

Learn how to use power integrity simulations and measurements during the design phase to reduce power rail noise and avoid EMI failures.

Broadcast Date: September 9, 2020
Duration: 60 min.    

In this live stream presentation, you will learn about advanced automotive radar system modeling techniques of unique radar waveform designs.

Original Broadcast Date: September 17, 2020
Duration: 60 min.    

PathWave ADS 2021 is here!  Come see our expert application engineers give you a fast-paced fly-by of the best new technologies introduced this year for Signal and Power integrity simulation.

Broadcast Date: October 1, 2020
Duration: 60 min.    

High-frequency circuit designers often struggle with stability. Learn techniques to identify and solve stability problems in the design phase before they become headaches in the lab. Classical methodologies will be discussed, and a unique approach will be introduced using a new bidirectional impedance probe in PathWave Advanced Design System (ADS) called the “Winslow Probe”.

Original Broadcast Date: October 22, 2020
Duration: 60 min.    

This webinar will show how modern design tools can be used to successfully assemble and simulate multiple technologies integrated into a Wafer Scale Package.

Original Broadcast Date: November 12, 2020
Duration: 60 min.    

Join us for a look at Keysight’s new Design Cloud user-experience for Electromagnetic Simulations in PathWave ADS 2021.  In this webinar, you will learn about the workflow, benefits, and performance expectations for a selection of RF/uW and Signal Integrity application examples. 

Furthermore, you will be introduced to our turn-key cloud solution partners, Nimbix, where you will see a live demonstration of PathWave ADS 2021 provisioning hardware on-the-fly on the Nimbix JARVICE platform.

Broadcast Date: November 18, 2020
Duration: 60 min.    

Interested to know how to replace IP1 and IP3 by spec compliant EVM for all the latest standard of wireless communications? In this webinar, you will learn how PathWave ADS will seamlessly use Keysight grade modulated sources, quickly compute EVM, improve your design vs system level metrics, assess improvements of PAs with embedded DPD algorithms, and also generate a representative model of your circuit to be handed over to your system teams for further comprehensive architecture analyses with PathWave System Design.

Original broadcast date: December 17, 2020
Duration: 60 min.    

In this webinar, you will learn how to assemble and analyze multi-technology components to achieve design wins in this competitive market and see how RFPro 3DEM-circuit co-simulation is iteratively used during design tweaks; and not just as a final sign off verification before hardware fabrication.