이 페이지를 찾으시나요? 추천 검색 결과 보기:

 

전문가 상담

기술 지원

전자 측정

모델 번호 입력:

1-25 / 162

정렬방식:
Keysight EEsof EDA Videos on YouTube
YouTube channel of Keysight EEsof EDA Videos

기본 데모 2018-11-26

How to Solve Signal Integrity Problems: The Basics
How to Solve Signal Integrity Problems: The Basics shows you how to use basic signal integrity (SI) analysis techniques such as eye diagrams, S-parameters, time-domain reflectometry (TDR) and single pulse response to solve signal integrity problems.

사용방법 동영상 2018-09-18

How to Design for Power Integrity: Optimizing Decoupling Capacitors
This short video will show how to optimize the decoupling capacitors for your next power delivery network.

사용방법 동영상 2018-06-01

Perform on-wafer RF calibration – WMS Series Part 5 of 6
In this video, we demonstrate an on wafer network analyzer calibration to 50 GHz.

기본 데모 2018-05-09

Automated on-wafer millimeter wave measurements demo – WMS Series Part 2 of 6
In this demo, we measure S-parameters on a GaAs MESFET and capacitor structure in an automated fashion across the wafer. This leverages a lot of pieces together that will be explained in later videos: • configuring the WaferPro Express software to drive other instruments and wafer prober software • wafer alignment • RF S-parameter calibration • WaferPro Express project set up

기본 데모 2018-05-09

Align wafer probes and create a wafer map – WMS Series Part 4 of 6
In this video, we demonstrate how to align a wafer to the reference plane of our probing system using the auto align feature in Velox. We will then generate a wafer map.

기본 데모 2018-05-09

Introduction to Wafer-level Measurement Solutions (WMS) – WMS Series Part 1 of 6
In this video we present an overview of the hardware and software used for making wafer level measurements up to 110 GHz.This is part of a 6 part video series on wafer level measurements.

기본 데모 2018-05-09

Set up a measurement project with WaferPro Express – WMS Series Part 6 of 6
In this video, we will set up a new project in WaferPro Express, defining our measurements on our desired devices.

기본 데모 2018-05-09

Configure WaferPro Express for measurements and probing – WMS Series Part 3 of 6
In this video, we will show you how to connect WaferPro Express to the instruments and then to the Velox prober control software.

기본 데모 2018-05-09

How to Avoid Costly Mistakes in Designing Phased Array Systems
This video will show how to avoid 3 costly steps in designing a phased array. 1) Not predicting the failure of spurious emission masks (SEM) in simulation, which leads to higher development cost and missing time to market windows. 2) Not exploring thoroughly in one simulation, which leads to blind angles. 3) Relying primarily on spreadsheet calculations, which leads to longer design and development cycles.

사용방법 동영상 2018-02-01

IEEE 802.11ax: Overcoming Design and Test Challenges with 89600 VSA Software
The IEEE 802.11ax introduces various new technologies and features to meet its goal of higher efficiency, capacity and coverage for a better user experience, especially for dense deployment. These new technologies increase design complexity and create a number of new test challenges. This video covers key IEEE 802.11ax transmitter design and test challenges and how to overcome those challenges with Keysight’s 89600 VSA software.

기본 데모 2017-10-02

IEEE 802.11ax: Physical Layer Overview
This video provides an overview of the IEEE 802.11ax WLAN standard highlighting the major physical layer technologies and features that are different from legacy WLAN standards.

기본 데모 2017-10-02

Top 10 New Signal Integrity and Power Integrity Features in ADS 2017
Advanced Design System (ADS) 2017 is coming soon and here are the top 10 new and exciting Signal Integrity (SI) and Power Integrity (PI) features. The new features aim to save engineers’ time and increase productivity.

기본 데모 2017-09-16

전력 전자장치의 ADS를 위한 퀵 스타트 가이드(영어)
이 가이드는 높은 di/dt 전력 전자장치를 위한 ADS 시작 방법: PCB 트레이스의 기생 레이아웃 EM 기반 모델의 회로 시뮬레이션 통합에 대해 설명합니다.

기본 데모 2017-08-15

How to Estimate Voltage Spikes from Layout Parasitic Inductance in Switched-Mode Power Supplies
We showed you how to deal with layout parasitic inductance in our previous video entitled “How to design DC-to-DC power converters”, but a frequently asked question was “When should I start to worry about layout parasitics inductance? Is there a quick rule of thumb that says kind of ‘Caution: Further investigation’s needed?’” The answer is yes and this follow up video is about how to make these estimates.

사용방법 동영상 2017-07-17

How to Simplify Device Model Extraction using an Open Source User Interface
This video shows an example of an IC-CAP custom user interface (UI) for device modeling. In the selected modeling application, the DC modeling of a Zener diode is intentionally kept simple in order to demonstrate the features of the UI.

사용방법 동영상 2017-06-26

EDAcafé - DAC 2017 Interview: Michel Azarian, Silicon RFIC EDA Program Manager
Sanjay Gangal from EDAcafé interviews Michel Azarian (Keysight Technologies' Silicon RFIC EDA Program Manager) at Design Automation Conference (DAC) 2017.

기본 데모 2017-06-22

IMS 2017: Top 5 Must-See 5G Products
Sponsored by Qorvo, Wireless Design and Development (WDD) counts down the best 5G products out of this year's International Microwave Symposium.

기본 데모 2017-06-19

Time & Frequency Domain Simulation-to-Measurement Techniques by Mike Resso
This presentation discusses a step-by-step process that signal integrity engineers can follow to ensure their success in designing with USB Type-C devices.

기본 데모 2017-06-18

Video Clips from the "Four Ways to Boost Simulation Data Processing using Python" Webcast
Watch these powerful video clips from the Keysight webcast, "Four Ways to Boost Simulation Data Processing using Python".

기본 데모 2017-06-12

Static Random Access Memory (SRAM) Cell Modeling in MBP 2017
This video introduces a new turnkey solution for SRAM modeling now available in Keysight’s Model Builder Program 2017. The video describes the concept of SRAM cell modeling and highlights the major challenges of that process.

기본 데모 2017-06-12

Sierra Circuits Interviews Heidi Barnes at DesignCon
During DesignCon 2017, Sierra Circuits interviewed Heidi Barnes, Senior Applications Engineer at Keysight Technologies and recipient of the DesignCon Engineer of the Year Award.

기본 데모 2017-06-07

Electrothermal Simulation using the Wolfspeed ADS PDK
This is a short demonstration of how the Wolfspeed ADS PDK is configured to work with the ADS electrothermal simulator to co-simulate electrical and thermal performance. This allows designers to quickly understand the impact of thermal effects on their circuit designs, and account for those effects during the design process.

기본 데모 2017-06-02

Power Integrity Ecosystem by Heidi Barnes from Keysight
This Power Integrity overview provides an understanding of power integrity, why it is important, how to design for it, and it teaches techniques for high-fidelity simulation, analysis and measurement.

기본 데모 2017-05-29

How to Extract a BSIM4 DC Model
This video introduces a general DC modeling and characterization flow for the BSIM4 model, which is one of the most popular models used by the industry today for bulk CMOS.

사용방법 동영상 2017-05-24

1 2 3 4 5 6 7 다음