Practical Power Sourcing and Measurement Considerations
This webinar will focus on the on the practical aspects of using power supplies and electronic loads in an application. If you’ve ever wanted to optimize your power instrument for your application, then these topics will be of great interest to you.
RF UW MMW Measurements
Superconductor and Spin Qubit Pre-Screening: Accelerate Quantum Development
A joint webinar by Keysight and FormFactor. Learn how to speed development cycles for advanced quantum development through an integrated measurement solution for pre-screening qubit devices at mK temperatures. The solution brings enormous benefits, like reducing development cycle times by 2X, providing critical qubit performance parameters at 50mK, and much more.
Modulation Distortion with Load Pull Webinar
Normalized loads and linear behavior are every amplifier designer’s dream, but highly variable environments require real-world ready solutions. In this webinar, you’ll learn how modulation distortion analysis under load pull conditions yields the lowest residual EVM, enables measurement repeatability, and allows realistic condition characterization.
Streamline Your RF Test Process: More Measurements With Less Complexity
Satellite system performance can be significantly impacted by signal distortion. Component testing typically relies on a test station for narrowband measurements such as S-parameter, IMD, IP3, then further testing at an additional test stand using a signal source and signal analyser for wideband characterization. It is now possible to simplify your test flow by performing both narrow-band and wide-band measurements at a single process step.
Automotive and Energy
Demystifying Five Everyday RF Measurements
A handheld analyzer serves as a very versatile tool in the field. They can help the user to analyze cables and antennas, scan for interference, measure 5G KPIs, and more, but they are only as good as the person who uses them. In this webinar, get to know five key RF measurements well so that one can be prepared for whatever challenges field presents to them: Learn more about Real-time Spectrum Analysis (RTSA), Noise Figure Measurements, Cable and Antenna Tests (CAT), Over-The-Air (OTA) testing, Electromagnetic Field (EMF) Exposure Evaluation etc.
Power Semiconductor Considerations for Converter Design
Power semiconductors are essential in power converter design, but data sheets often do not provide sufficient information for the circuit designer. This webinar is targeted at power circuit designers who may not have extensive power semiconductor knowledge, but who would like to understand better how to select the right power semiconductors to meet their converter design needs.
The Future of Battery, Battery-powered Wireless Devices and How to Test Them
Join this webinar to learn the Keysight solutions that will help address your battery and test challenges, whether you are a device designer or a battery manufacturer.
- Use cases for battery-powered wireless devices, cell design and manufacturing
- Keysight’s readily available solutions to characterize battery performance, optimize battery life, evaluate self-discharge quickly and more
Aerospace and Defense
O-RAN Radio Unit Conformance Testing Webinar
We will cover O-RAN radio unit (RU) conformance testing and the challenges associated with conducting these tests. In addition, Keysight's O-RU conformance test setup (including O-DU emulation, RF signal sources and analyzers, and Keysight's test automation framework) will be discussed to help you validate O-RAN conformance and performance of the open fronthaul implementation across RF and protocol measurement domains.
Base Station Signal Quality for 5G Private Networks Webinar
We will explore the 3GPP features that enable 5G private networks as well as the challenges posed by testing 5G base station transmitters in private networks. More specifically, we will discuss the best tips and tricks to optimize signal quality (EVM) measurement in 5G private networks and the latest in signal analysis to tackle your testing challenges. An accurate and insightful testing process will help your smart factories prepare, deploy, and operate faster while using network resources more efficiently and accurately.
5G Summit 2022 Day 1 - Delivering on 5G and 6G Vision Physical Layer
3GPP release 18 represents a major evolution of the 5G System to be branded as the first release of 5G Advanced. Among other improvements, Rel-18 will include major enhancements in the areas of artificial intelligence and extended reality that will enable highly intelligent network solutions that can support a wider variety of use cases than ever before.
6G research is in its very early stages. Going from100 Gbps to 1 Tbps is a key objective and an active area of research for 6G. However, it poses significant challenges, both from an RF perspective and baseband perspective. How do we make this happen?
5G Summit 2022 Day 2 - The O-RAN and Private Networks of the Future
O-RAN: The Next Big Thing in Telecom. It's representing mobile communication industry’s move toward an open, virtualized, and disaggregated architecture. O-RAN revolutionizes how mobile network operators (MNOs) can build their radio access networks (RANs) using a multivendor, interoperable, and autonomous supply ecosystem.
Leveraging O-RAN for smaller-scale private and venue networks is of interest to the mobile operators, systems integrators, cloud companies and RAN technology developers. How do we protect the integrity of the networks?
Join the 5G Summit day 2 to find out more.
PathWave Design 2023 Webinar Series
Welcome to the PathWave Design 2023 Webinar Series. This series of events covers the newest features and enhancements coming in the PathWave Design 2023 solutions for design and modeling engineers. It also demonstrates how Keysight’s customers are using PathWave EDA products to ensure more efficient and predictable design cycles.
Accurate Wideband Demodulation Webinar
Device specification, operation protocols, 3GPP standards--tough to design with, impossible to design without. In this webinar, you’ll learn how to measure symbol EVM (a metric which captures component characterization compared to a set of standards) of an amplifier using nothing more than a vector network analyzer (VNA) enabled with Modulation Distortion and PathWave Vector Signal Analysis software applications.
Keysight Design Forum Encon
Sign up now for the Keysight Design Forum replay to see announcements from Keysight experts, this replay includes core topics from Keysight Design Forum 2021. The seminars cover areas such as the basics of simulation, including design and development cases, as well as applications and demonstrations.
1.6T is the Future of Ethernet. Are You Ready?
1.6T is the future of data center networking. Make sure you’re ready with expert predictions, advice, and test solutions.
Join us as industry Ethernet experts discuss:
- Market trends driving the need for 224 Gbps speeds
- Technical challenges with 1.6T Ethernet and test solutions
- Optical and electrical innovations needed to make 1.6T a reality
Simulating for High-Speed Digital Insights
High-performance computing for embedded system applications is pushing the envelope for speed, a small form-factor, and the right price-point. Designers need to carefully balance material selection and PCB fabrication options, together with smart design strategies for vias, connectors and PCB trace routing. In this webinar we will walk through the simulation process that SECO Italy have undertaken to ensure design success.
Keysight Live From The Lab
Keysight Live From The Lab
On-Demand (7-10 June 2022)
Keysight Live from the Lab is a free, virtual event featuring engineering tips and tricks, expert Q&A to help you engineer faster. During this action-packed event, you’ll learn about Internet of Things (IoT) battery life testing, VNA component characterization, what’s coming next in 5G, and more.
Find webinars in other languages and time zones
Select your region