전문가 상담

기술 지원

전자 측정

모델번호로 검색: 예제: 34401A, E4440A

상세 분류

상세분류 제거

산업/기술

분야별 검색결과

1-25 / 1215

정렬방식:
How to Predict Package and Bondwire Effects on Your RF-Module Designs
This short video shows how to predict package, board, and bond wire effects on your RF-module designs which subsequently enables you to fix the design prior going to fabrication. The video demonstrates the process of building modules that comprise different technologies and performing EM simulation on them.

사용방법 동영상 2015-02-19

Keysight Network Analyzer - Youtube Playlist
Video demo playlist

기본 데모 2015-02-16

Introducing Keysight E5080A ENA Vector Network Analyzer - Demo
This video introduces the Keysight E5080A ENA vector network analyzer, which has the new touch-based GUI and offers the industry’s best combination of RF measurement performance and speed.

기본 데모 2015-02-12

MP4 MP4 49.80 MB
How to Use Envelope Tracking to Improve Power Amplifier Efficiency
This video introduces basic concepts regarding applying envelope tracking to improve power amplifier efficiency.

사용방법 동영상 2015-02-10

86100D Infiniium DCA-X Wide-Bandwidth Oscilloscopes Demo
Learn more about Keysight's 86100D DCA-X oscilloscopes. They perform precision measurements on high-speed digital designs from 50 Mb/s to more than 80 Gb/s on up to 16 channels simultaneously.

기본 데모 2015-02-04

PowerSuite 원버튼 전력 측정
전력 측정의 절대적 신뢰도를 높이려면 키사이트의 PowerSuite를 사용해야 하는데, 이것은 다양한 신호 및 스펙트럼 분석기에 기본적으로 설치되어 있습니다.

기본 데모 2015-02-02

Satellite Monitoring Using the Keysight M9393A PXIe VSA & 89600 VSA Software on YouTube

기본 데모 2015-01-30

AC 전력 분석기 - PA2201A – 유튜브 동영상
새로운 PA2201A의 실제 사용 사례 보기

기본 데모 2015-01-29

How to Setup and Run Load Pull Simulations: The Basics
This video introduces basic concepts regarding running load pull simulations. It then uses load pull simulation to find a load impedance that enables you to obtain greater than 43 dBm output power and greater than 55% PAE from a Cree FET.

사용방법 동영상 2015-01-27

How to Make Accurate, Automated RF Wafer-level Measurements
The video introduces automation as a way to increase productivity and efficiency. Keysight WaferPro Express measurement software is used to illustrate the various steps in combination with Cascade Microtech Velox software for prober control and Cascade WinCalXE software for automated calibration.

사용방법 동영상 2015-01-27

How to Design an RF Power Amplifier: Class F
This short video will provide an introduction to Class F Power Amplifier Design by first building a nonlinear device model and then using this model in a circuit simulation environment to generate the idealized “square” Class F waveforms.

사용방법 동영상 2015-01-27

Physical Layer Test System (PLTS) with PXI-VNA Multiport Measurements - Demo
This demonstration shows you how to measure 32 interconnect devices using a PXI VNA with PLTS software for multi-port multi-domain device characterization. This is a cost effective solution that provides insight into channel performance.

기본 데모 2015-01-27

MP4 MP4 12.53 MB
How to Characterize and Optimize Connector to Board Transition Designs
This video demonstrates how to accurately model an SMA to PCB transition to obtain agreement between simulated and measured results and how to improve the transition performance.

사용방법 동영상 2015-01-15

How to Design an RF Power Amplifier: The Basics
This video provides a foundation for understanding how power amplifier circuits work. If you are new to High Frequency Power Amplifier Circuit Design, this is the place to start.

사용방법 동영상 2015-01-15

How to Design an RF Power Amplifier: Class A, AB and B
This video provides an introduction to the most basic modes of power amplifier operation by first building a nonlinear device model from scratch and then using this model in a circuit simulation environment to demonstrate various modes of power amplifier operation.

사용방법 동영상 2015-01-15

Keysight EEsof EDA "How to" Videos
A collection of "How to" videos from Keysight EEsof EDA.

사용방법 동영상 2015-01-15

How to Apply EM Port Calibration to Improve Simulation Accuracy (MoM)
This video covers 5 different Momentum calibration methods and shows how the different types of calibration methods impact simulation results along with where and how to use them properly.

사용방법 동영상 2015-01-15

How to Design RF and Microwave Impedance Matching Networks
This video describes how to design RF and Microwave impedance matching networks.

사용방법 동영상 2015-01-14

How to Extract SRAM Models
This video shows how to extract SRAM device models efficiently on Keysight's device modeling platform.

사용방법 동영상 2015-01-14

How to Use “Design of Experiments” to Create Robust Designs With High Yield
This video explains how to use the DOE methodology to help you create and produce robust designs with first pass success and high yield.

사용방법 동영상 2015-01-14

How to Optimize the Performance of Your RF Layout
This video shows a practical and effective approach to optimize the performance of your RF layout by parameterizing it and performing EM optimization prior to going to fabrication – thus helping to achieve fist pass success.

사용방법 동영상 2015-01-14

LIN Symbolic Trigger and Decode
Learn how to symbolically decode and trigger on a LIN bus using Keysight's InfiniiVision X-Series oscilloscopes.

기본 데모 2015-01-09

MOV MOV 46.45 MB
CAN FD Eye-Diagram Mask Testing
Learn how perform an eye diagram mask test on a CAN FD bus.

기본 데모 2015-01-09

MOV MOV 68.37 MB
Infiniium 90000 Q-시리즈 오실로스코프 데모 동영상
90000 Q-시리즈 오실로스코프가 업계 최고의 대역폭에서도 가장 빠른 신호를 있는 그대로 표시하는 방법을 확인해보십시오.

기본 데모 2015-01-07

Keysight Silicon RFIC Design Solutions
In this video we show the Keysight Silicon RFIC design solutions that help you achieve your goals for designing today´s challenging RFICs and successfully going beyond the IC to verify its performance in higher levels of integration.

기본 데모 2015-01-05

1 2 3 4 5 6 7 8 9 10 ... 다음