Discutez avec un expert

Support technique

Mesure Electronique

Recherche par numéro de modèle du produit: Exemples : 34401A, E4440A

Affiner la liste

retirer tout le raffinement

Par type de contenu

1-25 sur 161

Sort:
Measuring Stress-Strain Curves for Shale Rock by Dynamic Instrumented Indentation - Application Note
Study of Dynamic instrumented indentation as an ideal way to measure the mechanical properties of shale rock. Note includes samples that can be just a few millimeters in extent, and shows that ion-milling is an adequate method of surface preparation. The note proves that test forces greater than 300mN, the primary results (reduced modulus and hardness) are accurate, repeatable, and relevant.

Notes d’application 2014-06-02

PDF PDF 1.59 MB
Introduction to SECM and Combined AFM-SECM - Application Note

Notes d’application 2014-05-07

PDF PDF 962 KB
Combining Atomic Force Microscopy with Scanning Electrochemical Microscopy - Application Note

Notes d’application 2014-05-07

PDF PDF 1.44 MB
New Investigations into Energy: Keysight Nanomeasurement Systems - Application Note
The data presented demonstrates just a few of the ways in which the latest atomic force microscopy (AFM), nanoindentation, and field-emission scanning electron microscope can be utilized to enhance energy-related materials research.

Notes d’application 2014-04-24

PDF PDF 3.67 MB
Rapid Mechanical Properties of Multi-layer Film Stacks - Application Note
In this note, we measure the mechanical properties of 50nm films with remarkable precision and accuracy. The precision is due to Express Test, which performs indentations at a rate of one per second, thereby allowing many indentations to be included in the final determination of modulus and hardness.

Notes d’application 2014-02-17

PDF PDF 2.29 MB
Mechanical Properties Measurement on Individual Composite Micro-fibers - Application Note
Study of characterization of mechanical properties of bicomponent micro-fibers, consisting of nylon 6 nano-islands in a PET sea, under tensile loading.

Notes d’application 2014-02-07

PDF PDF 188 KB
Mapping the Mechanical Properties of SAC 305 Solder with Express Test - Application Note
The note discusses the use of nano-indentation to map the mechanical properties of a SAC 305 solder joint, because electronic reliability depends on mechanical integrity. Traditional nano-indentation testing time for such mapping, would have been prohibitively long but with the Express Test we were able to generate quantitative and highly resolved hardness maps in about an hour.

Notes d’application 2013-12-18

PDF PDF 205 KB
MAC Mode Imaging of Biological Molecules with 7500 AFM - Application Note

Notes d’application 2013-11-21

PDF PDF 163 KB
CSM and DCM-Express Nanoindentation Mapping on Lithium.Polymer Battery Composites
investigattion of the the mechanical properties of a lithium rechargeable battery cathode by using both the classic XP CSM and the new DCM Express Test method.

Notes d’application 2013-11-05

PDF PDF 427 KB
Contact Deformation of LiNbO3 Single Crystal:Dislocations, Twins and Ferroelectric Domains
A Study of a combined nanoindentation and AFM investigation showing that twinning and dislocation motion are two major deformation mechanisms under contact loading in periodically poled (0001) LiNbO3.

Notes d’application 2013-11-01

PDF PDF 752 KB
Determining Critical Stresses in Semiconductors: Using ZnO Crystal & GaN Freestanding Film
A study of the nanoindenter G200 used to perform spherical nanoindentation experiments on ZnO single crystal and GaN freestanding film.

Notes d’application 2013-10-30

PDF PDF 363 KB
Differentiating Surface Mechanical Properties with Dynamic Lateral Force Microscopy-Application Note

Notes d’application 2013-10-26

PDF PDF 331 KB
High Resolution Imaging with 7500 AFM - Application Note

Notes d’application 2013-10-24

PDF PDF 520 KB
Humidity-dependent AFM Nanolithography - Application Note

Notes d’application 2013-10-21

PDF PDF 128 KB
Mapping the Mechanical Properties of Cement-based Materials Using CSM &Ultra-fast Nanoindentation
Study of hydration mechanisms of a commercial cement paste that has been h investigated with the use of the G200 using innovative statistical ultra-fast nanoindentation.

Notes d’application 2013-10-15

PDF PDF 930 KB
Tribology of Dental Enamel: Effect of Etching - Application Brief
In this summary, the nano-tribological behavior of the dental enamel as a function of acid etching is characterized using a nanoindenter.

Notes d’application 2013-10-09

PDF PDF 214 KB
Nanotribology of Hard Thin Film Coatings: A Case Study Using the G200 Nanoindenter
Case study of the changes in elastic modulus and hardness of thin film as measured using the nanoindenter and the continuous stiffness measurement option, which measures the mechanical properties as a continuous function of depth.

Notes d’application 2013-09-30

PDF PDF 469 KB
In Situ Electrochemical Measurements Using the 7500 AFM - Application Note

Notes d’application 2013-09-27

PDF PDF 142 KB
Elastic Modulus Mapping Using the 7500 AFM - Application Note

Notes d’application 2013-09-24

PDF PDF 234 KB
Single Molecule Force Spectroscopy (SMFS) Using the 7500 AFM - Application Note

Notes d’application 2013-09-24

PDF PDF 226 KB
Vapor Annealing Effect on Copolymers Studied by 7500 AFM with Environmental Control-Application Note

Notes d’application 2013-09-16

PDF PDF 184 KB
The Revolutionary Impact of the Oliver and Pharr Technique on the Science of Hardness Testing
Explanation of the Oliver-Pharr method and how it can be used to obtain an equivalent Vickers hardness number

Notes d’application 2013-09-13

PDF PDF 120 KB
Surface Potential Measurements Using the Keysight 7500 AFM - Application Note

Notes d’application 2013-09-13

PDF PDF 452 KB
Humidity-dependent Surface Chemistry Studied by 7500 Atomic Force Microscopy - Application Note

Notes d’application 2013-09-12

PDF PDF 157 KB
Magnetic Force Microscopy Studies Using the Keysight 7500 AFM - Application Note

Notes d’application 2013-09-12

PDF PDF 524 KB

1 2 3 4 5 6 7 Page suivante