Contact an Expert

Technical Support

Electronic Measurement

Find by Product Model Number: Examples: 34401A, E4440A

151-175 of 843

Sort:
How do I add an option to my 89601AN license ?
In this FAQ you will find information on how to upgrade your 89601AN license with a new option.

FAQ 2012-09-06

How do I update my license for use with a newer version of 89601AN software?
In this FAQ you will find information on how to update your 89601AN license for use with a new version.

FAQ 2012-09-06

How do I license my 89601AN software for the first time?
In this FAQ you will find information on how to license your 89601AN software.

FAQ 2012-09-06

How to calculate the bit clock frequency under DSI interface of U8903A?
The Bit clock frequency can be calculated by multipling the number of channels,bit length and frame clock frequency.

FAQ 2012-08-25

Are there limit lines with pass/fail status on FieldFox instruments?
Yes, all the modes include limit lines and pass/fail status indicators.

FAQ 2012-08-20

Can I use a Keysight 85032E Cal Kit with FieldFox instruments?
Yes. You can use an 85032E Cal kit with FieldFox.

FAQ 2012-08-20

Is it possible to modify the scale on the return loss plot when the measurement is configured for Return Loss & DTF on a FieldFox instrument?
There is no method to change the scale on the upper Return Loss (top) plot.

FAQ 2012-08-20

Will FieldFox instruments be able to differentiate between internal and external zeroing when using the U200xA/B/H USB power sensors?
FieldFox instruments cannot do this differentiation, but FieldFox allows you the choice of external zeroing.

FAQ 2012-08-20

How Can I Identify Boards Revision in FieldFox?
See instructions.

FAQ 2012-08-20

What is the start frequency of FieldFox instruments?
Standard is 2 MHz

FAQ 2012-08-20

Can I Use a LAN Connection with my FieldFox?
Yes. Read the scenarios...

FAQ 2012-08-20

Why Do I Get a "Meas UNCAL" Message During Zero Span Measurement in Signal Analyzer Mode?
The “Meas UNCAL” message during zero span measurements indicates that the capacity of the capture memory has been exceeded for the current combination of RBW and sweep time.

FAQ 2012-08-17

What Keysight measurement hardware front-ends are supported by the 89601A VSA Software?
The supported measurement hardware frontends include the 89600S VXI mainframes, and certain models of the E4406 VSA, ESA-E spectrum analyzers, PSA spectrum analyzers, and Infiniium oscilloscopes.

FAQ 2012-08-17

Can I Use FieldFox in an Explosive Area?
It was not intentionally designed for use in a hazardous environment or explosive atmosphere. To use a FieldFox in a hazardous environment is the decision of the end-user.

FAQ 2012-08-17

How Do Recalibrate the FieldFox Battery Pack?
Use N9910X-872 to recalibrate the battery pack.

FAQ 2012-08-17

Can I Use a USB External Storage Devices?
Yes. It is recommended to use FAT32 formatted drive.

FAQ 2012-08-17

Why won't my FieldFox Turn On?
Most often power on issues occur when battery has been completely discharged.

FAQ 2012-08-17

FieldFox will not recognize my USB memory stick. What can I do?
Most USB memory sticks work well with the FieldFox.

FAQ 2012-08-17

Why Do I Get an Install Error Message When I Try to Upgrade my Firmware?
The likely cause is a conflicting file name.

FAQ 2012-08-17

Why are N9910X Accessories Packed with the Original Supplier Packaging and Labels?
It allows customers to purchase common accessories easier.

FAQ 2012-08-17

How Can I Find What I Need in a Signal Analyzer Recording Faster?
If you have a very long Signal Analyzer recording, it is sometimes difficult to find the area of interest. There is no really good tool for this problem at this time, but here are some suggestions.

FAQ 2012-08-17

Why Does FieldFox Sometimes Revert to a Zero Serial Number at Power On?
The firmware needs to be upgraded to ≥ A.03.02.

FAQ 2012-08-15

Why won't my Signal Analyzers Display Pulse Type Signals Properly?
These signals may be missed if the Sweep Acquisition setting is on Auto. We recommend using a Sweep Acquisition setting of 50 or 100 for GSM signals.

FAQ 2012-08-15

Which is Most Accurate: CalReady, QuickCal (Without Load), or 2 Port Calibration?
When nothing connected at the end of RF port, CalReady is the most accurate calibration method at test port.

FAQ 2012-08-15

Is the Instrument Control Toolbox required for all versions of Download Assistant?
Download Assistant V2.0 requires you to have MATLAB’s Instrument Control Toolbox installed.

FAQ 2012-08-09

Previous 1 2 3 4 5 6 7 8 9 10 ... Next