Discuter avec un expert

Amplifiers

Keysight offers design, simulation and test capability for all of your RF and microwave amplifier design and test needs.

Designers of low-noise amplifiers and power amplifiers can use harmonic balance simulation in Advanced Design System (ADS) to characterize gain compression and noise. Keysight Ptolemy simulation and Circuit Envelope simulation can be used to characterize amplifiers with digital modulation signals.

After designing your amplifier and building a prototype, you can utilize Keysight test equipment to verify your designs. Keysight products include Network Analyzers, Spectrum Analyzers, Signal Sources, Oscilloscopes and more, all for your amplifier test requirements.

1-25 sur 69

Tri:
IMS 2015 Demos from Keysight EEsof EDA 
YouTube video playlist containing International Microwave Symposium (IMS) 2015 demo videos from Keysight EEsof EDA MicroApps.

Démonstration de base 2015-06-19

 
Determining the Best RF Simulation Tools as an RF Consulting Engineer 
Independent consulting in RF and microwave engineering is a growing trend and many engineers are delivering their highly sought after RF expertise back to the industry.

Article 2015-06-08

PDF PDF 2.64 MB
How to Design an RF Power Amplifier: Class J 
This short video will provide an introduction to Class J Power Amplifiers and demonstrate a superior, time saving methodology to design and practically realize a Class J RF power amplifier. First,a theoretical approach will be used to design an ideal circuit from first principles and then circuit design tools will be utilized to synthesize a more realistic circuit topology from the ideal case. The design process will be illustrated using a commercially available GaN MMIC device from Qorvo.

Vidéos pratiques 2015-05-07

 
Drive Down the Cost of Test Using the ENA Series of Network Analyzers - Application Note 
In this application note, we discuss the contributions of Keysight Technologies, Inc.’s ENA Series of Vector Network Analyzers (ENA, hereafter) to drive down the cost of test in production lines.

Notes d’application 2015-05-01

PDF PDF 2.46 MB
Keysight EEsof EDA "How To Design Power Amplifier" Videos 
A collection of "How to Design Power Amplifier" Videos from Keysight EEsof EDA.

Vidéos pratiques 2015-04-22

 
How to Design an RF Power Amplifier: Class E 
This video provides an introduction to Class E Power Amplifiers and demonstrates a superior, time saving methodology to design and practically realize a Class E RF power amplifier using first principles to build an ideal circuit and then utilizing circuit design tools to synthesize a more realistic circuit topology from the ideal case.

Vidéos pratiques 2015-03-11

 
How to Use Envelope Tracking to Improve Power Amplifier Efficiency 
This video introduces basic concepts regarding applying envelope tracking to improve power amplifier efficiency.

Vidéos pratiques 2015-02-10

 
M9068A Phase Noise X-Series Measurement Application for PXI Vector Signal Analyzers 
This document provides technical and other information related to the Phase Noise X-Series measurement application for modular instruments.

Présentation technique 2015-02-10

PDF PDF 2.39 MB
How to Make Accurate, Automated RF Wafer-level Measurements 
The video introduces automation as a way to increase productivity and efficiency. Keysight WaferPro Express measurement software is used to illustrate the various steps in combination with Cascade Microtech Velox software for prober control and Cascade WinCalXE software for automated calibration.

Vidéos pratiques 2015-01-27

 
How to Design an RF Power Amplifier: Class F 
This short video will provide an introduction to Class F Power Amplifier Design by first building a nonlinear device model and then using this model in a circuit simulation environment to generate the idealized “square” Class F waveforms.

Vidéos pratiques 2015-01-27

 
How to Setup and Run Load Pull Simulations: The Basics 
This video introduces basic concepts regarding running load pull simulations. It then uses load pull simulation to find a load impedance that enables you to obtain greater than 43 dBm output power and greater than 55% PAE from a Cree FET.

Vidéos pratiques 2015-01-27

 
How to Design an RF Power Amplifier: Class A, AB and B 
This video provides an introduction to the most basic modes of power amplifier operation by first building a nonlinear device model from scratch and then using this model in a circuit simulation environment to demonstrate various modes of power amplifier operation.

Vidéos pratiques 2015-01-15

 
How to Design an RF Power Amplifier: The Basics  
This video provides a foundation for understanding how power amplifier circuits work. If you are new to High Frequency Power Amplifier Circuit Design, this is the place to start.

Vidéos pratiques 2015-01-15

 
How to Design RF and Microwave Impedance Matching Networks 
This video describes how to design RF and Microwave impedance matching networks.

Vidéos pratiques 2015-01-14

 
How to Use “Design of Experiments” to Create Robust Designs With High Yield 
This video explains how to use the DOE methodology to help you create and produce robust designs with first pass success and high yield.

Vidéos pratiques 2015-01-14

 
How to Optimize the Performance of Your RF Layout 
This video shows a practical and effective approach to optimize the performance of your RF layout by parameterizing it and performing EM optimization prior to going to fabrication – thus helping to achieve fist pass success.

Vidéos pratiques 2015-01-14

 
Transmit/Receive Module Test Platform (TRM-X) - Technical Overview 
The TRM-X Test Platform, measurement science expertise and systems when and where needed, provide the capability you need to deliver AESA radar; datalink; and satcom transmit/receive modules.

Présentation technique 2015-01-10

PDF PDF 1.83 MB
The Impact of Electro-Thermal Coupling on HBT Power Amplifiers 
This paper describes the use of electrothermal simulation to understand, predict, and account for cross-circuit thermal coupling in a commercial HBT power amplifier.

Notes d’application 2014-10-19

 
Keysight Technologies Introduces Design and Test Solutions at European Microwave Week 
Keysight announces that it will demonstrate a wide range of new, high-performance flexible test solutions at the European Microwave Week 2014, Oct. 7–9, Rome, Fiera di Roma, Booth F100. The test solutions are used by engineers for designing and testing components for radar systems, antennas and next-generation wireless devices.

Dossier de presse 2014-09-03

 
GoldenGate RFIC Solutions 
This brochure highlights the benefits of the GoldenGate RFIC Simulator.GoldenGate is the most trusted simulation, analysis and verification solution available for integrated RF circuit design within Cadence Virtuoso.

Brochure 2014-09-03

PDF PDF 954 KB
Simulating Envelope Tracking with Advanced Design System Software - Application Note 
This example applies envelope tracking to an example amplifier to show techniques of using Advanced Design System (ADS) for this type of design.

Notes d’application 2014-08-02

PDF PDF 2.38 MB
Keysight EEsof EDA Premier Communications Design Software - Technical Overview 
Keysight EEsof EDA premier communications design software product overview brochure.

Brochure 2014-07-31

PDF PDF 1015 KB
Digital Predistortion Linearizes Wireless Power Amplifiers 
This Article by Wan-Jong Kim, Shawn P. Stapleton, Jong Heon Kim, and Cory Edelman focuses on how digital predistortion linearizes wireless power amplifiers.

Article 2014-07-31

PDF PDF 1.81 MB
Genesys 2014 Delivers Breakthrough Modulated RF Analysis for Circuit, System Design 
Keysight announces the latest release of Genesys 2014.

Dossier de presse 2014-05-27

 
S-Parameter Measurements on Multiport Devices – In-Phase Technologies 
S-Parameter Measurements on Multiport Devices from In-Phase Technologies and Keysight

Brefs de solution 2014-04-30

 

1 2 3 Page suivante